In the present study, we tested the feasibility of actuation of microplates by fringing electrostatic fields, i.e., field lines between plates and the sidewalls supporting them. Unlike the common close-gap actuation mechanism usually used in these kinds of devices, we present an alternative operational principle based on an electrostatic fringe field for the actuation of micro electromechanical (MEMS) plates, which is especially beneficial for open air environment operation. In order to validate the actuation principle, a circular MEMS plate was considered and an analytical model was built. The electrostatic force applied to the plate was extracted from a solution of a steady boundary value problem of a cylinder and was validated numerically using finite element simulation. This was followed by a solution of the plate governing equation of motion using an expansion theorem. Devices of two different geometries were fabricated and operated. Actuation of the plates by means of the fringing field was demonstrated experimentally. The proposed architecture and actuation principle is advantageous and overcomes many of the difficulties encountered in microplates electrostatically actuated by a close-gap electrode. Due to the absence of a small gap, the device is not prone to pull-in instability and stiction and is not subjected to squeeze-film damping. Moreover, since the actuation is separated from the front side of the device, open air contaminations, such as humidity or dust, cannot cause operational failure. In addition, the device is especially beneficial for mass sensing in an open environment, as well as flow senors where a flush-mounted smooth surface is important.
Issue Section:
Research Papers
Topics:
Boundary-value problems,
Damping,
Manufacturing,
Microplates,
Plates (structures),
Pressure,
Resonance,
Vibration,
Silicon,
Simulation,
Displacement,
Cylinders,
Electric fields,
Electrodes,
Sensors,
Semiconductor wafers,
Geometry,
Microelectromechanical systems,
Frequency response,
Equations of motion,
Finite element analysis
References
1.
Kuntzman
, M. L.
, Garcia
, C. T.
, Onaran
, A. G.
, Avenson
, B.
, Kirk
, K. D.
, and Hall
, N. A.
, 2011
, “Performance and Modeling of a Fully Packaged Micromachined Optical Microphone
,” J. Microelectromech. Syst.
, 20
(4
), pp. 828
–833
.10.1109/JMEMS.2011.21481642.
Ya'akobovitz
, A.
, and Krylov
, S.
, 2011
, “Large Angle Silicon-on-Insulator Tilting Actuator With Kinematic Excitation and Simple Integrated Parallel-Plate Electrostatic Transducer
,” Jpn. J. Appl. Phys., Part 1
, 50
(11R
), p. 117201
.10.7567/JJAP.50.1172013.
Ya'akobovitz
, A.
, and Krylov
, S.
, 2010
, “Toward Sensitivity Enhancement of MEMS Accelerometers Using Mechanical Amplification Mechanism
,” IEEE Sens. J.
, 10
(8
), pp. 1311
–1319
.10.1109/JSEN.2009.20397514.
Milanovic
, V.
, Last
, M.
, and Pister
, K.
, 2003
, “Laterally Actuated Torsional Micromirrors for Large Static Deflection
,” IEEE Photonics Technol. Lett.
, 15
(2
), pp. 245
–247
.10.1109/LPT.2002.8060855.
Ya'akobovitz
, A.
, Krylov
, S.
, and Shacham-Diamand
, Y.
, 2008
, “Large Angle SOI Tilting Actuator With Integrated Motion Transformer and Amplifier
,” Sens. Actuators, A
, 148
(2
), pp. 422
–436
.10.1016/j.sna.2008.08.0206.
Haluzan
, D. T.
, Klymyshyn
, D. M.
, Börner
, M.
, Achenbach
, S.
, Wells
, G.
, Mappes
, T.
, and Mohr
, J.
, 2008
, “Stiction Issues and Actuation of RF LIGA-MEMS Variable Capacitors
,” Microsyst. Technol.
, 14
(9–11
), pp. 1709
–1714
.10.1007/s00542-008-0583-67.
Porfiri
, M.
, 2009
, “An Electromechanical Model for Sensing and Actuation of Ionic Polymer Metal Composites
,” Smart Mater. Struct.
, 18
(1
), p. 015016
.10.1088/0964-1726/18/1/0150168.
Castro
, L.
, Ferreira
, A.
, Bertoluzza
, S.
, Batra
, R.
, and Reddy
, J.
, 2010
, “A Wavelet Collocation Method for the Static Analysis of Sandwich Plates Using a Layerwise Theory
,” Compos. Struct.
, 92
(8
), pp. 1786
–1792
.10.1016/j.compstruct.2010.01.0219.
Gilhooley
, D.
, Batra
, R.
, Xiao
, J.
, McCarthy
, M.
, and Gillespie
, J.
, Jr., 2007
, “Analysis of Thick Functionally Graded Plates by Using Higher-Order Shear and Normal Deformable Plate Theory and MLPG Method With Radial Basis Functions
,” Compos. Struct.
, 80
(4
), pp. 539
–552
.10.1016/j.compstruct.2006.07.00710.
Chan
, C.-K.
, Lai
, W.-C.
, Wu
, M.
, Wang
, M.-Y.
, and Fang
, W.
, 2011
, “Design and Implementation of a Capacitive-Type Microphone With Rigid Diaphragm and Flexible Spring Using the Two Poly Silicon Micromachining Processes
,” IEEE Sens. J.
, 11
(10
), pp. 2365
–2371
.11.
Lee
, I.
, Yoon
, G.
, Park
, J.
, Seok
, S.
, Chun
, K.
, and Lee
, K.
, 2005
, “Development and Analysis of the Vertical Capacitive Accelerometer
,” Sens. Actuators, A
, 119
(1
), pp. 8
–18
.10.1016/j.sna.2004.06.03312.
Acar
, C.
, and Shkel
, A.
, 2004
, “Structural Design and Experimental Characterization of Torsional Micromachined Gyroscopes With Non-Resonant Drive Mode
,” J. Micromech. Microeng.
, 14
(1
), pp. 15
–25
.10.1088/0960-1317/14/1/30313.
Kwon
, S.
, Milanovic
, V.
, and Lee
, L.
, 2004
, “Vertical Combdrive Based 2-D Gimbaled Micromirrors With Large Static Rotation by Backside Island Isolation
,” IEEE J. Sel. Top. Quantum Electron.
, 10
(3
), pp. 498
–504
.10.1109/JSTQE.2004.82849314.
Zhu
, Y.
, and Espinosa
, H.
, 2004
, “Reliability of Capacitive RF MEMS Switches at High and Low Temperatures
,” Int. J. RF Microwave Comput. Aided Eng.
, 14
(4
), pp. 317
–328
.10.1002/mmce.2001515.
Lee
, H.-C.
, Park
, J.-V.
, and Park
, Y.-H.
, 2007
, “Development of Shunt Type Ohmic RF MEMS Switches Actuated by Piezoelectric Cantilever
,” Sens. Actuators, A
, 136
(1
), pp. 282
–290
.10.1016/j.sna.2006.10.05016.
Yoshida
, K.
, Kikuchi
, M.
, Park
, J.
, and Yokota
, S.
, 2002
, “Fabrication of Micro Electro-Rheological Valves (ER Valves) by Micromachining and Experiments
,” Sens. Actuators, A
, 95
(2–3
), pp. 227
–233
.10.1016/S0924-4247(01)00730-017.
Berns
, A.
, Buder
, U.
, Obermeier
, E.
, Wolter
, A.
, and Leder
, A.
, 2006
, “AeroMEMS Sensor Array for High-Resolution Wall Pressure Measurements
,” Sens. Actuators A: Phys.
, 132
(1
), pp. 104–111
.10.1016/j.sna.2006.04.05618.
Ko
, C.
, and Chiou
, J.
, 2003
, “Optimal Design of the Magnetic Microactuator Using the Genetic Algorithm
,” J. Magn. Magn. Mater.
, 263
(1–2
), pp. 38
–46
.10.1016/S0304-8853(02)01533-019.
Xie
, T.
, Xie
, H.
, Fedder
, G.
, and Pan
, Y.
, 2003
, “Endoscopic Optical Coherence Tomography With a Modified Microelectromechanical Systems Mirror for Detection of Bladder Cancers
,” Appl. Opt.
, 42
(31
), pp. 6422
–6426
.10.1364/AO.42.00642220.
Filhol
, F.
, Defay
, E.
, Divoux
, C.
, Zinck
, C.
, and Delaye
, M.
, 2005
, “Resonant Micro-Mirror Excited by a Thin-Film Piezoelectric Actuator for Fast Optical Beam Scanning
,” Sens. Actuators, A: Phys.
, 123–124
, pp. 483
–489
.10.1016/j.sna.2005.04.02921.
Isamoto
, K.
, Kato
, K.
, Morosawa
, A.
, Chong
, C.
, Fujita
, H.
, and Toshiyoshi
, H.
, 2004
, “A 5-V Operated MEMS Variable Optical Attenuator by SOI Bulk Micromachining
,” IEEE J. Sel. Top. Quantum Electron.
, 10
(3
), pp. 570
–578
.10.1109/JSTQE.2004.82847522.
Batra
, R.-C.
, Porfiri
, M.
, and Spinello
, D.
, 2008
, “Effects of Van der Waals Force and Thermal Stresses on Pull-In Instability of Clamped Rectangular Microplates
,” Sensors
, 8
(2
), pp. 1048
–1069
.10.3390/s802104823.
Porfiri
, M.
, 2008
, “Vibrations of Parallel Arrays of Electrostatically Actuated Microplates
,” J. Sound Vib.
, 315
(4
), pp. 1071
–1085
.10.1016/j.jsv.2008.02.00724.
Nayfeh
, A. H.
, and Younis
, M. I.
, 2004
, “A New Approach to the Modeling and Simulation of Flexible Microstructures Under the Effect of Squeeze-Film Damping
,” J. Micromech. Microeng.
, 14
(2
), pp. 170
–181
.10.1088/0960-1317/14/2/00225.
Han
, C.-H.
, Choi
, D.-H.
, and Yoon
, Y.-B.
, 2011
, “Parallel-Plate MEMS Variable Capacitor With Superior Linearity and Large Tuning Ratio Using a Levering Structure
,” J. Microelectromech. Syst.
, 20
(6
), pp. 1345
–1354
.10.1109/JMEMS.2011.216765726.
Batra
, R.
, Porfiri
, M.
, and Spinello
, D.
, 2007
, “Review of Modeling Electrostatically Actuated Microelectromechanical Systems
,” Smart Mater. Struct.
, 16
(6
), pp. R23
–R31
.10.1088/0964-1726/16/6/R0127.
Elata
, D.
, Bochobza-Degani
, O.
, and Nemirovsky
, Y.
, 2003
, “Analytical Approach and Numerical Alpha-Lines Method for Pull-In Hyper-Surface Extraction of Electrostatic Actuators With Multiple Uncoupled Voltage Sources
,” J. Microelectromech. Syst.
, 12
(5
), pp. 681
–691
.10.1109/JMEMS.2003.81845628.
Guo
, Y.
, Pan
, Z.
, and Ward
, M.
, 2005
, “Touchdown and Pull-In Voltage Behavior of a MEMS Device With Varying Dielectric Properties
,” SIAM J. Appl. Math.
, 66
(1
), pp. 309
–338
.10.1137/04061339129.
Zhang
, Y.
, and Zhao
, Y.
, 2006
, “Numerical and Analytical Study on the Pull-In Instability of Micro-Structure Under Electrostatic Loading
,” Sens. Actuators A: Phys.
, 127
(2
), pp. 366
–380
.10.1016/j.sna.2005.12.04530.
Lemaire
, E.
, Rochus
, V.
, Golinval
, J. C.
, and Duysinx
, P.
, 2008
, “Microbeam Pull-In Voltage Topology Optimization Including Material Deposition Constraint
,” Comput. Meth. Appl. Mech. Eng.
, 197
(45–48
), pp. 4040
–4050
.10.1016/j.cma.2008.03.02431.
Rhoads
, J.
, Shaw
, S. W.
, and Turner
, K. L.
, 2008
, “Nonlinear Dynamics and Its Applications in Micro- and Nanoresonators
,” ASME
Paper No. DSCC2008-2406.10.1115/DSCC2008-240632.
Lucyszyn
, S.
, 2004
, “Review of Radio Frequency Microelectromechanical Systems Technology
,” IEEE Proc. Sci. Meas. Technol.
, 151
(2
), pp. 93
–103
.10.1049/ip-smt:2004040533.
Zhao
, Y.
, 2003
, “Stiction and Anti-Stiction in MEMS and NEMS
,” Acta Mech. Sin.
, 19
(1
), pp. 1
–10
.10.1007/BF0248744834.
Younis
, M. I.
, and Nayfeh
, A. H.
, 2004
, “Simulation of Squeeze-Film Damping of Microplates Actuated by Large Electrostatic Load
,” ASME J. Comput. Nonlinear Dyn.
, 2
(3
), pp. 232
–241
.10.1115/1.272749135.
Batra
, R. C.
, Porfiri
, M.
, and Spinello
, D.
, 2006
, “Electromechanical Model of Electrically Actuated Narrow Microbeams
,” J. Microelectromech. Syst.
, 15
(5
), pp. 1175
–1189
.10.1109/JMEMS.2006.88020436.
Boutaayamou
, M.
, Sabariego
, R. V.
, and Dular
, P.
, 2008
, “Finite Element Modeling of Electrostatic MEMS Including the Impact of Fringing Field Effects on Forces
,” Sens. Lett.
, 6
(1
), pp. 115
–120
.10.1166/sl.2008.00637.
Chowdhury
, S.
, Ahmadi
, M.
, and Miller
, W.
, 2006
, “Pull-In Voltage Study of Electrostatically Actuated Fixed-Fixed Beams Using a VLSI On-Chip Interconnect Capacitance Model
,” J. Microelectromech. Syst.
, 15
(3
), pp. 639
–651
.10.1109/JMEMS.2005.86378438.
Yeh
, J.
, Hui
, C.
, and Tien
, N.
, 2000
, “Electrostatic Model for an Asymmetric Combdrive
,” J. Microelectromech. Syst.
, 9
(1
), pp. 126
–135
.10.1109/84.82578739.
Johnson
, W.
, and Warne
, L.
, 1995
, “Electrophysics of Micromechanical Comb Actuators
,” J. Microelectromech. Syst.
, 4
(1
), pp. 49
–59
.10.1109/84.36537040.
Tang
, W. C.
, Lim
, M. G.
, and Howe
, R. T.
, 1992
, “Electrostatic Comb Drive Levitation and Control Method
,” J. Microelectromech. Syst.
, 1
(4
), pp. 170
–178
.10.1109/JMEMS.1992.75250841.
Tilleman
, M.
, 2004
, “Analysis of Electrostatic Comb-Driven Actuators in Linear and Nonlinear Regions
,” Int. J. Solids Struct.
, 41
(18–19
), pp. 4889
–4898
.10.1016/j.ijsolstr.2004.04.03442.
Hammer
, H.
, 2010
, “Analytical Model for Comb-Capacitance Fringe Fields
,” J. Microelectromech. Syst.
, 19
(1
), pp. 175
–182
.10.1109/JMEMS.2009.203783343.
Chiou
, J.
, and Lin
, Y.
, 2005
, “A Novel Large Displacement Electrostatic Actuator: Pre-Stress Comb-Drive Actuator
,” J. Micromech. Microeng.
, 15
(9
), pp. 1641
–1648
.10.1088/0960-1317/15/9/00544.
Greywall
, D.
, Pai
, C.
, Oh
, S.
, Chang
, C.
, Marom
, D.
, Busch
, P.
, Cirelli
, R.
, Taylor
, J.
, Klemens
, F.
, Sorsch
, T.
, Bower
, J.
, Lai
, W.
, and Soh
, H.
, 2003
, “Monolithic Fringe-Field-Activated Crystalline Silicon Tilting-Mirror Devices
,” J. Microelectromech. Syst.
, 12
(5
), pp. 702
–707
.10.1109/JMEMS.2003.81806845.
Chen
, Z.
, and Luo
, R.
, 1998
, “Design and Implementation of Capacitive Proximity Sensor Using Microelectromechanical Systems Technology
,” IEEE Trans. Ind. Electron.
, 45
(6
), pp. 886
–894
.10.1109/41.73533246.
Langfelder
, G.
, Longoni
, A. F.
, Tocchio
, A.
, and Lasalandra
, E.
, 2011
, “MEMS Motion Sensors Based on the Variations of the Fringe Capacitances
,” IEEE Sens. J.
, 11
(4
), pp. 1069
–1077
.10.1109/JSEN.2010.207849947.
Ya'akobovitz
, A.
, and Krylov
, S.
, 2012
, “Influence of Perforation on Electrostatic and Damping Forces in Thick SOI MEMS Structures
,” J. Micromech. Microeng.
, 22
(11
), p. 115006
.10.1088/0960-1317/22/11/11500648.
Carslaw
, H.
, and Jaeger
, J.
, 1959
, Conduction of Heat in Solids
, 2nd ed., Oxford University
, London
.49.
Senturia
, S.
, 2001
, Microsystem Design
, Kluwer Academic Publishers
, Boston, MA
.50.
Seely
, S.
, 1962
, Electromechanical Energy Conversion
, McGraw-Hill
, New York
.51.
Batra
, R. C.
, Porfiri
, M.
, and Spinello
, D.
, 2008
, “Reduced-Order Models for Microelectromechanical Rectangular and Circular Plates Incorporating the Casimir Force
,” Int. J. Solids Struct.
, 45
(11–12
), pp. 3558
–3583
.10.1016/j.ijsolstr.2008.02.01952.
Reddy
, J.
, 1999
, Theory and Analysis of Elastic Plates and Shells
, Taylor & Francis
, Philadelphia, PA
.53.
Adhikari
, S.
, 2006
, “Damping Modelling Using Generalized Proportional Damping
,” J. Sound. Vib.
, 293
(1–2
), pp. 156
–170
.10.1016/j.jsv.2005.09.03454.
Angeles
, J.
, and Ostrovskaya
, S.
, 2002
, “The Proportional-Damping Matrix of Arbitrarily Damped Linear Mechanical Systems
,” ASME J. Appl. Mech.
, 69
(5
), pp. 649
–656
.10.1115/1.148383255.
Craig
, R.
, and Kurdila
, A.
, 2006
, Fundamentals of Structural Dynamics
, Wiley
, New York
.56.
Pan
, F.
, Kubby
, J.
, Peeters
, E.
, Tran
, A. T.
, and Mukherjee
, S.
, 1998
, “Squeeze Film Damping Effect on the Dynamic Response of a MEMS Torsion Mirror
,” J. Micromech. Microeng.
, 8
(3
), pp. 200
–208
.10.1088/0960-1317/8/3/00557.
Starr
, J. B.
, 1990
, “Squeeze-Film Damping in Solid-State Accelerometers
,” IEEE Solid-State Sensor and Actuator Workshop
, 4th Technical Digest, Hilton Head Island, SC, June 4–7, pp. 44
–47
.10.1109/SOLSEN.1990.10981758.
Langlois
, W. E.
, 1961
, “Isothermal Squeeze Films
,” Defense Technical Information Center, Fort Belvoir, VA, Report No. 261094.59.
Ono
, T.
, and Esashi
, M.
, 2004
, “Mass Sensing With Resonating Ultra-Thin Silicon Beams Detected by a Double-Beam Laser Doppler Vibrometer
,” Meas. Sci. Technol.
, 15
(10
), pp. 1977
–1981
.10.1088/0957-0233/15/10/00560.
Krylov
, S.
, Molinazzi
, N.
, Shmilovich
, T.
, Pomerantz
, U.
, and Lulinsky
, S.
, 2010
, “Parametric Excitation of Flexural Vibrations of Micro Beams by Fringing Electrostatic Fields
,” ASME
Paper No. DETC2010-28684.10.1115/DETC2010-2868461.
Alkharabsheh
, S. A.
, and Mohammad
, Y. I.
, 2013
, “Statics and Dynamics of MEMS Arches Under Axial Forces
,” ASME J. Vib. Acoust.
, 135
(2
), p. 021007
.10.1115/1.402305562.
Carr
, D. W.
, Evoy
, S.
, Sekaric
, L.
, Craighead
, H.
, and Parpia
, J.
, 2000
, “Parametric Amplification in a Torsional Microresonator
,” Appl. Phys. Lett.
, 77
(10
), pp. 1545
–1547
.10.1063/1.130827063.
Evoy
, S.
, Carr
, D.
, Sekaric
, L.
, Olkhovets
, A.
, Parpia
, J.
, and Craighead
, H.
, 1999
, “Nanofabrication and Electrostatic Operation of Single-Crystal Silicon Paddle Oscillators
,” J. Appl. Phys.
, 86
(11
), pp. 6072
–6077
.10.1063/1.37165664.
Su
, X.
, and Yang
, H.
, 2001
, “Design of Compliant Microleverage Mechanisms
,” Sens. Actuators A: Phys.
, 87
(3
), pp. 146
–156
.10.1016/S0924-4247(00)00488-X65.
Adiga
, V.
, Ilic
, B.
, Barton
, R.
, Wilson-Rae
, I.
, Craighead
, H.
, and Parpia
, J.
, 2012
, “Approaching Intrinsic Performance in Ultra-Thin Silicon Nitride Drum Resonators
,” J. Appl. Phys.
, 112
(6
), p. 064323
.10.1063/1.475457666.
Kottapalli
, A.
, Tan
, C.
, Olfatnia
, M.
, Miao
, J.
, Barbastathis
, G.
, and Triantafyllou
, M.
, 2011
, “A Liquid Crystal Polymer Membrane MEMS Sensor for Flow Rate and Flow Direction Sensing Applications
,” J. Micromech. Microeng.
, 21
(8
), p. 085006
.10.1088/0960-1317/21/8/08500667.
Wen
, C.-C.
, and Fang
, W.
, 2008
, “Tuning the Sensing Range and Sensitivity of Three Axes Tactile Sensors Using the Polymer Composite Membrane
,” Sens. Actuators A: Phys.
, 145–146
, pp. 14
–22
.10.1016/j.sna.2007.10.01168.
Wang
, X.
, Engel
, J.
, and Liu
, C.
, 2003
, “Liquid Crystal Polymer (LCP) for MEMS: Processes and Applications
,” J. Micromech. Microeng.
, 13
(5
), pp. 628
–633
.10.1088/0960-1317/13/5/31469.
Su
, X.
, and Yang
, H.
, 2001
, “Two-Stage Compliant Microleverage Mechanism Optimization in a Resonant Accelerometer
,” Struct. Multidiscip. Opt.
, 22
(4
), pp. 328
–334
.10.1007/s00158-001-0153-370.
Ilic
, B.
, Yang
, Y.
, Aubin
, K.
, Reichenbach
, R.
, Krylov
, S.
, and Craighead
, H.
, 2005
, “Enumeration of DNA Molecules Bound to a Nanomechanical Oscillator
,” Nano Lett.
, 5
(5
), pp. 925
–929
.10.1021/nl050456k71.
Chiu
, H.-Y.
, Hung
, P.
, Postma
, H. W. C.
, and Bockrath
, M.
, 2008
, “Atomic-Scale Mass Sensing Using Carbon Nanotube Resonators
,” Nano Lett.
, 8
(12
), pp. 4342
–4346
.10.1021/nl802181cCopyright © 2014 by ASME
You do not currently have access to this content.
