This paper describes preliminary results from a systematic analytical study of the improvement of damping in polymer composites at the micromechanical level under transverse normal loading by the use of special fiber coatings. Since shear deformations are important in damping of viscoelastic polymers, and large shear strains are generated in the region of the fiber/matrix interface, one idea for improving damping is to put a fiber coating made from a highly dissipative material in this region. A finite element model based on a “representative volume element” or repeating element of a continuously reinforced coated fiber composite is used to study damping under transverse normal loading. The micromechanical composite model investigated is a unidirectional graphite/epoxy with an acrylic polymer as the fiber coating material. Both two and three dimensional finite element models are analyzed in order to compare the influence of plane stress and plane strain conditions on the damping and stiffness properties of the composite micromechanical model. Parametric studies are conducted by using a two dimensional plane strain finite element model in order to illustrate how the coating applied to the fiber influences dynamic properties of the composite structure. The parametric studies are done with particular emphasis on the effects of frequency, temperature, and fiber coating thickness on the damping of the composite structure.

Issue Section:
Research Papers
Topics:
Coatings, Damping, Fibers, Polymer composites, Composite materials, Finite element model, Plane strain, Shear (Mechanics), Deformation, Elastomers, Epoxy adhesives, Epoxy resins, Graphite, Polymers, Stiffness, Stress, Temperature
1.
Chaturvedi
S. K.
, and
Tzeng
G. Y.
,
1991
, “
Micromechanical Modeling of Material Damping in Discontinuous Fiber Three Phase Polymer Composites
,”
Composites Engineering
, Vol.
1
, pp.
49
–
60
.
2.
Davis
L. C.
,
1993
, “
Residual Stresses and Their Effects on Deformation in Particle-Reinforced Metal-Matrix Composites
,”
Metalurgical Transactions A
, Vol.
24A
, pp.
2487
–
2496
.
3.
Drzal
L. T.
,
Rich
M. J.
,
Koenig
M. F.
, and
Lloyd
P. F.
,
1983
, “
Adhesion of Graphite Fibers to Epoxy Matrices: II. The Effect of Fiber Finish
,”
J. Adhesion
, Vol.
16
, pp.
133
–
152
.
4.
Finegan, I. C., 1997, “Analytical and Experimental Study of Improvement of Damping at the Micromechanical Level in Polymer Composite Materials by the Use of Special Fiber Coatings,” Wayne State University, Detroit, Michigan, Ph. D. Dissertation, 1997.
5.
Gibson, R. F., and Cartian, I., 1993, “Improvement and Optimization of Damping in Advanced Composite Materials-A Review,” Proceedings of the 1993 SEM 50th Anniversary Spring Conference and Exposition, Society for Experimental Mechanics, Bethel, Connecticut, pp. 682–693.
6.
Gibson
R. F.
,
Chaturvedi
S. K.
, and
Sun
C. T.
,
1982
, “
Complex Moduli of Aligned Discontinuous Fibre Reinfirced Polymer Composites
,”
J. Materials Science
, Vol.
17
, pp.
3499
–
3509
.
7.
Gibson, R. F., Hwang, S. J., and Kwak, H., 1991, “Micromechanical Modeling of Damping in Composites Including Interphase Effects,” Proceedings of 36th International SAMPE Symposium, Vol. 1, pp. 592–606.
8.
Gibson
R. F.
,
1992
, “
Damping Characteristics of Composite Materials and Structures
,”
J. of Materials Engineering and Performance
, Vol.
1
, pp.
11
–
20
.
9.
Gibson, R. F., 1994, Principles of Composite Material Mechanics, McGraw-Hill, Inc., New York.
10.
Hwang
S. J.
, and
Gibson
R. F.
,
1992
, “
The Use of Strain Energy—Based Finite Element Techniques in the Analysis of Various Aspects of Damping of Composite Materials and Structures
,”
J. of Composite Materials
, Vol.
26
, No.
17
, pp.
2585
–
2605
.
11.
Mantena, P. R., and Gibson, R. F., 1990, “Dynamic Mechanical Properties of Hybrid Polyethylene/Graphite Composites,” Proc. 22nd Int. SAMPE Tech. Conference, pp. 370–382.
12.
PATRAN Plus, User Manual, Release 2.5, Oct. 1990, PDA Eng., Patran Division, Costa Mesa, Cahfornia.
13.
P/FEA, User Manual, Release 2.5, Jan., 1991, PDA Eng., Patran Division, Costa Mesa, California.
14.
Rotz, C. A., and Barrett, D. J., 1991, “Cocured Damping Layers in Composite Structures,” Proc. 23rd Int. SAMPE Tech. Conference, pp. 352–363.
15.
Suarez
S. A.
,
Gibson
R. F.
,
Sun
C. T.
, and
Chaturvedi
S. K.
,
1986
, “
The Influence of Fiber Length and Fiber Orientation on Damping and Stiffness of Polymer Composite Materials
,”
Experimental Mechanics
, Vol.
26
, No.
2
, pp.
175
–
184
.
16.
Ungar
E. E.
, and
Kerwin
E. M.
,
1962
, “
Loss Factors of Viscoelastic Systems in Terms of Energy Concepts
,”
J. of the Acoustical Society of America
, Vol.
34
, No.
7
, pp.
954
–
958
.
This content is only available via PDF.
Copyright © 1998
 by The American Society of Mechanical Engineers
You do not currently have access to this content.