A pressure-correction based, 3D Navier-Stokes CFD code was used to simulate the effects of turbine parameters on the tip leakage flow and vortex in a linear turbine cascade to understand the detailed flow physics. A baseline case simulation of a cascade was first conducted in order to validate the numerical procedure with experimental measurements. The effects of realistic tip clearance spacing, inlet conditions, and relative endwall motion were then sequentially simulated, while maintaining previously modified parameters. With each additional simulation, a detailed comparison of the leakage flow’s direction, pressure gradient, and mass flow, as well as the leakage vortex and its roll-up, size, losses, location, and interaction with other flow features, was conducted. Part I of this two-part paper focuses on the effect of reduced tip clearance height on the leakage flow and vortex. Reduced tip clearance results in less mass flow through the gap, a smaller leakage vortex, and less aerothermal losses in both the gap and the vortex. The shearing of the leakage jet and passage flow to which leakage vortex roll-up is usually attributed to is not observed in any of the simulations. Alternative explanations of the leakage vortex’s roll-up are presented. Additional secondary flows that are seen near the casing are also discussed.
Skip Nav Destination
e-mail: jat@turbo3.aero.psu.edu
e-mail: bllaer@engr.psu.edu
Article navigation
April 2001
Technical Papers
Numerical Simulation of Tip Leakage Flows in Axial Flow Turbines, With Emphasis on Flow Physics: Part I—Effect of Tip Clearance Height
J. Tallman, Graduate Research Assistant,
e-mail: jat@turbo3.aero.psu.edu
J. Tallman, Graduate Research Assistant
Center for Gas Turbine and Power, Pennsylvania State University, 153-J Hammond Bldg., University Park, PA 16802
Search for other works by this author on:
B. Lakshminarayana, Evan Pugh Professor and Director
e-mail: bllaer@engr.psu.edu
B. Lakshminarayana, Evan Pugh Professor and Director
Center for Gas Turbine and Power, Pennsylvania State University, 153-J Hammond Bldg., University Park, PA 16802
Search for other works by this author on:
J. Tallman, Graduate Research Assistant
Center for Gas Turbine and Power, Pennsylvania State University, 153-J Hammond Bldg., University Park, PA 16802
e-mail: jat@turbo3.aero.psu.edu
B. Lakshminarayana, Evan Pugh Professor and Director
Center for Gas Turbine and Power, Pennsylvania State University, 153-J Hammond Bldg., University Park, PA 16802
e-mail: bllaer@engr.psu.edu
Contributed by the International Gas Turbine Institute and presented at the 45th International Gas Turbine and Aeroengine Congress and Exhibition, Munich, Germany, May 8–11, 2000. Manuscript received by the International Gas Turbine Institute February 2000. Paper No. 2000-GT-514. Review Chair: D. Ballal.
J. Turbomach. Apr 2001, 123(2): 314-323 (10 pages)
Published Online: February 1, 2000
Article history
Received:
February 1, 2000
Citation
Tallman, J., and Lakshminarayana, B. (February 1, 2000). "Numerical Simulation of Tip Leakage Flows in Axial Flow Turbines, With Emphasis on Flow Physics: Part I—Effect of Tip Clearance Height ." ASME. J. Turbomach. April 2001; 123(2): 314–323. https://doi.org/10.1115/1.1368881
Download citation file:
Get Email Alerts
Related Articles
Aerodynamics of Tip Leakage Flows Near Partial Squealer Rims in an Axial Flow Turbine Stage
J. Turbomach (January,2005)
Numerical Simulation of Tip Leakage Flows in Axial Flow Turbines, With Emphasis on Flow Physics: Part II—Effect of Outer Casing Relative Motion
J. Turbomach (April,2001)
Related Proceedings Papers
Related Chapters
Numerical Simulations of Tip Leakage Vortex Cavitation Flows Around a NACA0009 Hydrofoil
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Large Eddy Simulations of a Confined Tip-Leakage Cavitating Flow with Special Emphasis on Vortex Dynamics
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Aerodynamic Performance Analysis
Axial-Flow Compressors