1-9 of 9
Keywords: cold rolling
Close
Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Article Type: Research Papers
J. Tribol. October 2021, 143(10): 101703.
Paper No: TRIB-20-1165
Published Online: February 5, 2021
... predictive formulae for the coefficient have been presented in the technical literature. Contradictions are observed, however, when their predictions are compared to each other. The data obtained while cold rolling aluminum and steel strips are used in the analyses. A model of the rolling process—accounting...
Journal Articles
Article Type: Research-Article
J. Tribol. February 2019, 141(2): 021606.
Paper No: TRIB-18-1196
Published Online: October 16, 2018
...Wenbo Qin; Jiansheng Li; Yaoyao Liu; Wen Yue; Chengbiao Wang; Qingzhong Mao; Yusheng Li The mechanical and tribological performances of 316 L stainless steel subjected to different cold rolling (CR) strains were investigated. The microhardness and strength of 316 L stainless steel were improved...
Journal Articles
Article Type: Research-Article
J. Tribol. October 2014, 136(4): 041502.
Paper No: TRIB-13-1203
Published Online: July 9, 2014
... stripe decreases the film thickness and increases the contact area ratio, pressure stress and friction stress. The surface roughness increases the contact area ratio, pressure stress and friction stress. inlet zone inlet film thickness cold rolling surface topography average flow theory...
Journal Articles
Article Type: Research Papers
J. Tribol. January 2011, 133(1): 012202.
Published Online: December 2, 2010
... roughness values reported in the first column of Table 4 are sheet annealed/pickled typical values; the values in the second column refer to a correct cold rolling process where the roll roughness is transferred to the sheet metal. If the pit defects are still present after the process, it means...
Journal Articles
Article Type: Technical Briefs
J. Tribol. April 2008, 130(2): 024503.
Published Online: April 24, 2008
...) and dimensionless maximum film temperature rise for high-speed lubricated cold rolling of strip incorporating various levels of starvations. These empirical relations are applicable for both fully flooded and starved conditions. Minimum film thickness (both isothermal and thermal) and maximum film temperature rise...
Journal Articles
Article Type: Technical Papers
J. Tribol. July 2003, 125(3): 670–677.
Published Online: June 19, 2003
.... , 1998 , “ A Mixed Lubrication Model for Cold Strip Rolling-Part I: Theoretical ,” STLE Tribol. Trans. , 41 ( 3 ), pp. 317 – 326 . Marsault, N., Montmitonnet, P., Deneuville, P., and Gratacos, P., 1998, “A Model of Mixed Lubrication for Cold Rolling of Strip,” Proc. NUMIFORM 98 , Twente University...
Journal Articles
Article Type: Technical Papers
J. Tribol. April 2003, 125(2): 384–390.
Published Online: March 19, 2003
...H. R. Le; M. P. F. Sutcliffe Theoretical models are presented for describing the evolution of pits in the inlet and work zone during cold rolling and strip drawing of shot-blast stainless steel under ‘mixed’ lubrication. Results shows that the rough shot-blast surface is flattened rapidly...
Journal Articles
Article Type: Technical Papers
J. Tribol. October 2001, 123(4): 791–798.
Published Online: December 7, 2000
... volume and area from drawing experiments on cold rolled stainless steel strip containing both artificial and stochastic roughness. Contributed by the Tribology Division for publication in the ASME JOURNAL OF TRIBOLOGY . Manuscript received by the Tribology Division June 22, 2000; revised manuscript...
Journal Articles
Article Type: Technical Papers
J. Tribol. January 2001, 123(1): 1–7.
Published Online: June 29, 2000
... hot band. For much smoother bright anneal strip, it is suggested that the presence of an oil film in the unpitted region prevents generation of pressure differences between the pits and the unpitted regions. A comparison of strip-drawn and cold-rolled stainless steel samples show that the change...