The dependence of the nanotribological properties of ultrathin amorphous carbon (a-C) films, deposited on Si(100) substrates by radio frequency sputtering, on their nanomechanical properties was investigated using surface force microscopy. The thickness and nanohardness of the a-C films were found to be in the range of 7–95 nm and 9–44 GPa, respectively. Sharp conical diamond tips with a 90 deg included angle and radius of curvature of about 20 μm and 100 nm were used to perform friction and wear experiments, respectively. The effect of the substrate compliance on the nanomechanical and nanotribological properties of the a-C films is interpreted in terms of the indentation depth and the film thickness. The coefficient of friction and wear rate of the a-C films are related to their nanomechanical properties, thickness, and surface roughness. The dependence of the coefficient of friction on contact load and the dominant friction mechanisms of elastically and plastically deformed films are discussed in light of friction force and surface imaging results. High effective hardness-to-elastic modulus ratio and low surface roughness characterize high wear resistance a-C films. Below a critical load, the steady-state removal rate of the film material is insignificantly small, revealing a predominantly elastic behavior.

Issue Section:
Technical Papers
Keywords:
carbon, films, nanotechnology, mechanical properties, atomic force microscopy, hardness, sputtered coatings, amorphous state, wear resistance, corrosion resistance
Topics:
Carbon films, Diamonds, Friction, Nanoscale phenomena, Sputtering (Irradiation), Stress, Surface roughness, Wear, Wear resistance, Mechanical properties, Atomic force microscopy, Deformation, Film thickness
1.
Binnig
,
G.
,
Quate
,
C. F.
, and
Gerber
,
Ch.
,
1986
, “
Atomic Force Microscope
,”
Phys. Rev. Lett.
,
56
, pp.
930
–
933
.
2.
Mate
,
C. M.
,
McClelland
,
G. M.
,
Erlandsson
,
R.
, and
Chiang
,
S.
,
1987
, “
Atomic-Scale Friction of a Tungsten Tip on a Graphite Surface
,”
Phys. Rev. Lett.
,
59
, pp.
1942
–
1945
.
3.
Kaneko
,
R.
,
Nonaka
,
K.
, and
Yasuda
,
K.
,
1988
, “
Scanning Tunneling Microscopy and Atomic Force Microscopy for Microtribology
,”
J. Vac. Sci. Technol. A
,
6
, pp.
291
–
292
.
4.
Kaneko, R., Oguchi, S., Miyamoto, T., Andoh, Y., and Miyake, S., 1990, “Micro-Tribology for Magnetic Recording,” Tribology and Mechanics of Magnetic Storage Systems, Vol. VII, STLE Special Publication SP-29, pp. 31–34.
5.
Miyamoto
,
T.
,
Kaneko
,
R.
, and
Miyake
,
S.
,
1991
, “
Tribological Characteristics of Amorphous Carbon Films Investigated by Point Contact Microscopy
,”
J. Vac. Sci. Technol. B
,
9
, pp.
1336
–
1339
.
6.
Miyamoto
,
T.
,
Miyake
,
S.
, and
Kaneko
,
R.
,
1993
, “
Wear Resistance of C+-Implanted Silicon Investigated by Scanning Probe Microscopy
,”
Wear
,
162–164
, pp.
733
–
738
.
7.
Lu
,
C. J.
,
Bogy
,
D.
, and
Kaneko
,
R.
,
1994
, “
Nanoindentation Hardness Tests Using a Point Contact Microscope
,”
ASME J. Tribol.
,
116
, pp.
175
–
180
.
8.
Wei
,
B.
, and
Komvopoulos
,
K.
,
1996
, “
Nanoscale Indentation Hardness and Wear Characterization of Hydrogenated Carbon Thin Films
,”
ASME J. Tribol.
,
118
, pp.
431
–
438
.
9.
Umemura
,
S.
,
Andoh
,
Y.
,
Hirono
,
S.
,
Miyamoto
,
T.
, and
Kaneko
,
R.
,
1996
, “
Nanoindentation and Nanowear Tests on Amorphous Carbon Films
,”
Philos. Mag. A
,
74
, pp.
1143
–
1157
.
10.
Lu
,
W.
, and
Komvopoulos
,
K.
,
1999
, “
Dependence of Growth and Nanomechanical Properties of Ultrathin Amorphous Carbon Films on Radio Frequency Sputtering Conditions
,”
J. Appl. Phys.
,
86
, pp.
2268
–
2277
.
11.
Lu
,
W.
, and
Komvopoulos
,
K.
,
1999
, “
Microstructure and Nanomechanical Properties of Nitrogenated Amorphous Carbon Thin Films Synthesized by Reactive Radio Frequency Sputtering
,”
J. Appl. Phys.
,
85
, pp.
2642
–
2651
.
12.
Lu, W., and Komvopoulos, K., 2001, “X-ray Photoelectron Spectroscopy and X-ray Auger Electron Spectroscopy Analysis of Radio Frequency Sputtered Amorphous Carbon Films,” J. Appl. Phys., in press.
13.
Lu
,
W.
,
Komvopoulos
,
K.
, and
Yeh
,
S. W.
,
2001
, “
Stability of Ultrathin Amorphous Carbon Films Deposited on Smooth Silicon Substrates by Radio Frequency Sputtering
,”
J. Appl. Phys.
,
89
, pp.
2422
–
2433
.
14.
Doerner
,
M. F.
, and
Nix
,
W. D.
,
1986
, “
A Method for Interpreting the Data from Depth-Sensing Indentation Instruments
,”
J. Mater. Res.
,
1
, pp.
601
–
609
.
15.
Kral
,
E. R.
,
Komvopoulos
,
K.
, and
Bogy
,
D. B.
,
1995
, “
Finite Element Analysis of Repeated Indentation of an Elastic-Plastic Layered Medium by a Rigid Sphere, Part I: Surface Results
,”
J. Appl. Mech.
,
62
, pp.
20
–
28
.
16.
King
,
R. B.
,
1987
, “
Elastic Analysis of Some Punch Problems for a Layered Medium
,”
Int. J. Solids Struct.
,
23
, pp.
1657
–
1664
.
17.
Bhattacharya
,
A. K.
, and
Nix
,
W. D.
,
1988
, “
Analysis of Elastic and Plastic Deformation Associated With Indentation Testing of Thin Films on Substrates
,”
Int. J. Solids Struct.
,
24
, pp.
1287
–
1298
.
18.
Kral
,
E. R.
,
Komvopoulos
,
K.
, and
Bogy
,
D. B.
,
1996
, “
Hardness of Thin-Film Media: Scratch Experiments and Finite Element Simulations
,”
ASME J. Tribol.
,
118
, pp.
1
–
11
.
19.
Bowden, F. P., and Tabor, D., 1950, Friction and Lubrication of Solids, Part I, Clarendon Press, Oxford, U.K.
20.
Johnson, K. L., 1985, Contact Mechanics, Cambridge University Press, Cambridge, U.K.
21.
Suh
,
N. P.
, and
Sin
,
H.-C.
,
1981
, “
The Genesis of Friction
,”
Wear
,
69
, pp.
91
–
114
.
22.
Komvopoulos
,
K.
,
Saka
,
N.
, and
Suh
,
N. P.
,
1985
, “
The Mechanism of Friction in Boundary Lubrication
,”
ASME J. Tribol.
,
107
, pp.
452
–
462
.
23.
Komvopoulos
,
K.
,
Saka
,
N.
, and
Suh
,
N. P.
,
1986
, “
Plowing Friction in Dry and Lubricated Metal Sliding
,”
ASME J. Tribol.
,
108
, pp.
301
–
313
.
24.
Wei
,
B.
, and
Komvopoulos
,
K.
,
1997
, “
Friction and Wear Micromechanisms of Amorphous Carbon Thin Films
,”
ASME J. Tribol.
,
119
, pp.
823
–
829
.
25.
Lu
,
W.
, and
Komvopoulos
,
K.
,
2000
, “
Implanted Argon Atoms as Sensing Probes of Residual Stress in Ultrathin Films
,”
Appl. Phys. Lett.
,
76
, pp.
3206
–
3208
.
Copyright © 2001
 by ASME
You do not currently have access to this content.