Abstract
The Morton effect (ME) occurs when a bearing journal experiences asymmetric heating due to synchronous vibration, resulting in thermal bowing of the shaft and increasing vibration. An accurate prediction of the journal's asymmetric temperature distribution is critical for reliable ME simulation. This distribution is strongly influenced by the film thermal boundary condition at the pad inlets. Part I utilizes machine learning (ML) to obtain a two-dimensional radial and axial distribution of temperatures over the leading-edge film cross section. The hybrid finite volume method (FVM)—bulk flow method of Part I eliminated film temperature discontinuities and is utilized in Part II for improving accuracy and efficiency of ME simulation.
Issue Section:
Hydrodynamic Lubrication
References
1.
Morton
, P. G.
, 1975
, “Some Aspects of Thermal Instability in Generators
,” G.E.C. Internal Report No. S/W40 u183
.2.
Hesseborn
, B.
, 1978
, “Measurements of Temperature Unsymmetries in Bearing Journal Due to Vibration
,” Internal Report ABB Stal
.3.
De Jongh
, F.
, 2008
, “The Synchronous Rotor Instability Phenomenon—Morton Effect
,” 37th Turbomachinery Symposium
, Houston, TX
, Sept. 8–11
, pp. 159
–167
.4.
Panara
, D.
, Panconi
, S.
, and Griffini
, D.
, 2015
, “Numerical Prediction and Experimental Validation of
Rotor Thermal Instability
,” 44th Turbomachinery Symposium
, Houston, TX
, Sept. 14–17
.5.
Tong
, X.
, Palazzolo
, A.
, and Suh
, J.
, 2017
, “A Review of the Rotordynamic Thermally Induced Synchronous Instability (Morton) Effect
,” ASME Appl. Mech. Rev.
, 69
(6
), p. 060801
. 6.
Keogh
, P.
, and Morton
, P.
, 1993
, “Journal Bearing Differential Heating Evaluation With Influence on Rotor Dynamic Behaviour
,” Proc. R. Soc. London, Ser. A
, 441
(1913
), pp. 527
–548
. 7.
Keogh
, P.
, and Morton
, P.
, 1994
, “The Dynamic Nature of Rotor Thermal Bending Due to Unsteady Lubricant Shearing Within a Bearing
,” Proc. R. Soc. London, Ser. A
, 445
(1924
), pp. 273
–290
. 8.
Gomiciaga
, R.
, and Keogh
, P.
, 1999
, “Orbit Induced Journal Temperature Variation in Hydrodynamic Bearings
,” ASME J. Tribol
, 121
(1
), pp. 77
–84
. 9.
Balbahadur
, A. C.
, and Kirk
, R.
, 2004
, “Part I—Theoretical Model for a Synchronous Thermal Instability Operating in Overhung Rotors
,” Int. J. Rotating Mach.
, 10
(6
), pp. 469
–475
. 10.
Balbahadur
, A. C.
, and Kirk
, R.
, 2004
, “Part II—Case Studies for a Synchronous Thermal Instability Operating in Overhung Rotors
,” Int. J. Rotating Mach
, 10
(6
), pp. 477
–487
. 11.
Murphy
, B.
, and Lorenz
, J.
, 2010
, “Simplified Morton Effect Analysis for Synchronous Spiral Instability
,” ASME J. Vib. Acoust.
, 132
(5
), p. 051008
. 12.
Childs
, D.
, and Saha
, R.
, 2012
, “A New, Iterative, Synchronous-Response Algorithm for Analyzing the Morton Effect
,” ASME J. Eng. Gas Turbines Power
, 134
(7
), p. 072501
. 13.
Lee
, J.
, and Palazzolo
, A.
, 2012
, “Morton Effect Cyclic Vibration Amplitude Determination for Tilt Pad Bearing Supported Machinery
,” ASME J. Tribol.
, 135
(1
), p. 011701
. 14.
Suh
, J.
, and Palazzolo
, A.
, 2014
, “Three-Dimensional Thermohydrodynamic Morton Effect Simulation—Part I: Theoretical Model
,” ASME J. Tribol.
, 136
(3
), p. 031706
. 15.
Suh
, J.
, and Palazzolo
, A.
, 2014
, “Three-Dimensional Thermohydrodynamic Morton Effect Analysis—Part II: Parametric Studies
,” ASME J. Tribol.
, 136
(3
), p. 031707
. 16.
Tong
, X.
, Palazzolo
, A.
, and Suh
, J.
, 2016
, “Rotordynamic Morton Effect Simulation With Transient, Thermal Shaft Bow
,” ASME J. Tribol.
, 138
(3
), p. 031705
. 17.
Tong
, X.
, and Palazzolo
, A.
, 2017
, “Double Overhung Disk and Parameter Effect on Rotordynamic Synchronous Instability—Morton Effect—Part I: Theory and Modeling Approach
,” ASME J. Tribol.
, 139
(1
), p. 011705
. 18.
Tong
, X.
, and Palazzolo
, A.
, 2017
, “Double Overhung Disk and Parameter Effect on Rotordynamic Synchronous Instability—Morton Effect—Part II: Occurrence and Prevention
,” ASME J. Tribol.
, 139
(1
), p. 011706
. 19.
Monmousseau
, P.
, and Fillon
, M.
, 2000
, “Transient Thermoelastohydrodynamic Analysis for Safe Operating Conditions of a Tilting-Pad Journal Bearing During Start-up
,” Tribol. Int.
, 33
(2
), pp. 225
–231
. 20.
Fillon
, M.
, Bligoud
, J. C.
, and Frene
, J.
, 1992
, “Experimental Study of Tilting-Pad Journal Bearings—Comparison With Theoretical Thermoelastohydrodynamic Results
,” ASME J. Tribol
, 114
(3
), pp. 579
–587
. 21.
Fillon
, M.
, and Bouyer
, J.
, “Thermohydrodynamic Analysis of a Worn Plain Journal Bearing
,” Tribol. Int.
, 37
(2
), pp. 129
–136
. 22.
Haugaard
, A. M.
, and Santos
, I. F.
, 2010
, “Multi-Orifice Active Tilting-Pad Journal Bearings—Harnessing of Synergetic Coupling Effects
,” Tribol. Int.
, 43
(8
), pp. 1374
–1391
. 23.
Brito
, F. P.
, Miranda
, A. S.
, Claro
, J. C. P.
, and Fillon
, M.
, 2012
, “Experimental Comparison of the Performance of a Journal Bearing With a Single and a Twin Axial Groove Configuration
,” Tribol. Int.
, 54
, pp. 1
–8
. 24.
Lin
, Q.
, Wei
, Z.
, Wang
, N.
, and Chen
, W.
, 2013
, “Analysis on the Lubrication Performances of Journal Bearing System Using Computational Fluid Dynamics and Fluid-Structure Interaction Considering Thermal Influence and Cavitation
,” Tribol. Int
, 64
, pp. 8
–15
. 25.
Brito
, F. P.
, Miranda
, A. S.
, Claro
, J. C. P.
, Teixeira
, J. C.
, Costa
, L.
, and Fillon
, M.
, 2014
, “The Role of Lubricant Feeding Conditions on the Performance Improvement and Friction Reduction of Journal Bearings
,” Tribol. Int.
, 72
, pp. 65
–82
. 26.
Yang
, J.
, and Palazzolo
, A.
, 2019
, “Three-Dimensional Thermo-Elasto-Hydrodynamic CFD Model of a Tilting Pad Journal Bearing-Part I: Static Response
,” ASME J. Tribol.
, 141
(6
), p. 061702
. 27.
Yang
, J.
, and Palazzolo
, A.
, 2020
, “Computational Fluid Dynamics Based Machine Learning Mixing Prediction for Tilt Pad Journal Bearing TEHD Modeling―Part I: Model Validation and Improvements
,” ASME J. Tribol.
, 143
(1
), p. 011801
. 28.
Yang
, J.
, and Palazzolo
, A.
, 2020
, “Computational Fluid Dynamics Based Machine Learning Mixing Prediction for Tilt Pad Journal Bearing TEHD―Part II: Artificial Neural Network Machine Learning
,” ASME J. Tribol.
, 143
(1
), p. 011802
. 29.
De Jongh
, F.
, and Van Der Hoeven
, P.
, 1998
, “Application of a Heat Barrier Sleeve to Prevent Synchronous Rotor Instability
,” 27th Turbomachinery Symposium
, Houston, TX
, Sept. 20–24
, pp. 17
–26
.30.
Oh
, J.
, Palazzolo
, A.
, and Hu
, L.
, 2020
, “Stability of Non-Axisymmetric Rotor and Bearing Systems Modeled With Three-Dimensional-Solid Finite Elements
,” ASME J. Vib. Acoust.
, 142
(1
), p. 011010
. 31.
Hagemann
, T.
, Zeh
, C.
, and Schwarze
, H.
, 2019
, “Heat Convection Coefficients of a Tilting-Pad Journal Bearing With Directed Lubrication
,” Tribol. Int.
, 136
, pp. 114
–126
. 32.
Tong
, X.
, and Palazzolo
, A.
, 2018
, “Tilting Pad Gas Bearing Induced Thermal Bow-Rotor Instability
,” Tribol. Int.
, 121
, pp. 269
–279
. 33.
Palazzolo
, A.
, 2016
, Vibration Theory and Applications With Finite Elements and Active Vibration Control
, Wiley
, New York, Chichester, UK
.Copyright © 2021 by ASME
You do not currently have access to this content.