Abstract
Despite the fabrication of particulate-reinforced composites via friction stir processing (FSP), an attempt was made to utilize FSP for the homogenization of filler dispersion in ZrB2/AA7075 in-situ composites fabricated via stir casting route, with varying weight percentages of ZrB2. The friction stir processing was performed for up to three passes with 100% overlap. The as-cast and friction stir processed (FSPed) composites were characterized for their microstructural, microhardness, and tribological behavior. The microstructural features revealed the increase in the misorientation angle among grain boundaries, with an increase in ZrB2 content and a number of FSP passes. Furthermore, the homogeneity of ZrB2 particles in the Al alloy matrix was significantly influenced by the number of FSP passes, which was quantified by Lorenz curves and Gini Indices. The FSPed alloy and composites exhibited higher microhardness as compared to their un-processed counterparts. The tribological behavior was investigated for three different load levels, i.e., 15 N, 30 N, and 45 N. The slope of the wear-rate at 45 N revealed that the Al-alloy exhibited a considerable increase in wear severity, whereas as-cast and FSPed composites did not show a significant increase. Both wear-rate and coefficient of friction decreased with an increase in the number of FSP passes and ZrB2 content. The scanning electron micrographs of worn surfaces confirmed the reduction in adhesion, abrasion, and delamination with the number of FSP passes. However, the synergism among the three depicted the overall tribological behavior.
Issue Section:
Friction and Wear
Keywords:
hardness,
X-ray analysis,
wear,
composites,
casting methods,
surface phenomena,
sliding,
wear mechanisms
References
1.
Sharma
, S.
, Nanda
, T.
, and Pandey
, O. P.
, 2018
, “Effect of Particle Size on dry Sliding Wear Behaviour of Sillimanite Reinforced Aluminium Matrix Composites
,” Ceram. Int.
, 44
(1
), pp. 104
–114
. 10.1016/j.ceramint.2017.09.1322.
Kumar
, P.
, and Srivastava
, V. K.
, 2016
, “A Review on Wear and Friction Performance of Carbon–Carbon Composites at High Temperature
,” Int. J. Appl. Ceram. Technol.
, 13
(4
), pp. 702
–710
. 10.1111/ijac.125383.
Rohatgi
, P. K.
, Tabandeh-Khorshid
, M.
, Omrani
, E.
, Lovell
, M. R.
, and Menezes
, P. L.
, 2013
, “Tribology of Metal Matrix Composites,” Tribology for Scientists and Engineers
, P. L.
Menezes
, M.
Nosonovsky
, S. P.
Ingole
, S. V.
Kailas
, and M. R.
Lovell
, eds., Springer
, New York
, pp. 233
–268
.4.
Sahoo
, P.
, and Davim
, J. P.
, 2013
, “Tribology of Ceramics and Ceramic Matrix Composites,” Tribology for Scientists and Engineers
, P. L.
Menezes
, M.
Nosonovsky
, S. P.
Ingole
, S. V.
Kailas
, and M. R.
Lovell
, eds., Springer
, New York
, pp. 211
–231
.5.
Kai
, X.
, Zhao
, Y.
, Wang
, A.
, Wang
, C.
, and Mao
, Z.
, 2015
, “Hot Deformation Behavior of in Situ Nano ZrB2 Reinforced 2024Al Matrix Composite
,” Compos. Sci. Technol.
, 116
, pp. 1
–8
. 10.1016/j.compscitech.2015.05.0066.
Bodunrin
, M. O.
, Alaneme
, K. K.
, and Chown
, L. H.
, 2015
, “Aluminium Matrix Hybrid Composites: a Review of Reinforcement Philosophies; Mechanical, Corrosion and Tribological Characteristics
,” J. Mater. Res. Technol.
, 4
(4
), pp. 434
–445
. 10.1016/j.jmrt.2015.05.0037.
Surappa
, M.
, 2003
, “Aluminium Matrix Composites: Challenges and Opportunities
,” Sadhana
, 28
(1–2
), pp. 319
–334
. 10.1007/BF027171418.
Kumar
, N.
, Gautam
, G.
, Gautam
, R. K.
, Mohan
, A.
, and Mohan
, S.
, 2016
, “Wear, Friction and Profilometer Studies of Insitu AA5052/ZrB2 Composites
,” Tribol. Int.
, 97
, pp. 313
–326
. 10.1016/j.triboint.2016.01.0369.
Poria
, S.
, Sahoo
, P.
, and Sutradhar
, G.
, 2016
, “Tribological Characterization of Stir-Cast Aluminium-TiB2 Metal Matrix Composites
,” Silicon
, 8
(4
), pp. 591
–599
. 10.1007/s12633-016-9437-510.
Rao
, R. N.
, and Das
, S.
, 2011
, “Effect of SiC Content and Sliding Speed on the Wear Behaviour of Aluminium Matrix Composites
,” Mater. Des.
, 32
(2
), pp. 1066
–1071
. 10.1016/j.matdes.2010.06.04711.
Zapata-Solvas
, E.
, Jayaseelan
, D.
, Lin
, H.-T.
, Brown
, P.
, and Lee
, W.
, 2013
, “Mechanical Properties of ZrB2-and HfB2-Based Ultra-High Temperature Ceramics Fabricated by Spark Plasma Sintering
,” J. Eur. Ceram. Soc.
, 33
(7
), pp. 1373
–1386
. 10.1016/j.jeurceramsoc.2012.12.00912.
Fu
, S.-Y.
, Feng
, X.-Q.
, Lauke
, B.
, and Mai
, Y.-W.
, 2008
, “Effects of Particle Size, Particle/Matrix Interface Adhesion and Particle Loading on Mechanical Properties of Particulate–Polymer Composites
,” Composites, Part B
, 39
(6
), pp. 933
–961
. 10.1016/j.compositesb.2008.01.00213.
Gupta
, A. K.
, Mallik
, B.
, and Roy
, D.
, 2020
, “Structure Property Correlation of In Situ Reinforced Al–Based Metal Matrix Composite via Stir Casting
,” Mater. Perform. Charact.
, 9
(1
), pp. 25
–35
. 10.1520/MPC2019003814.
Rozhbiany
, F. A. R.
, and Jalal
, S. R.
, 2019
, “Influence of Reinforcement and Processing on Aluminum Matrix Composites Modified by Stir Casting Route
,” Adv. Compos. Lett.
, 28
, p. 2633366X19896584
.15.
Zhang
, Z.
, Yang
, R.
, Li
, Y.
, Chen
, G.
, Zhao
, Y.
, and Liu
, M.
, 2018
, “Microstructural Evolution and Mechanical Properties of Friction Stir Processed ZrB2/6061Al Nanocomposites
,” J. Alloys Compd.
, 762
, pp. 312
–318
. 10.1016/j.jallcom.2018.05.21616.
Mishra
, R. S.
, Ma
, Z. Y.
, and Charit
, I.
, 2003
, “Friction Stir Processing: A Novel Technique for Fabrication of Surface Composite
,” Mater. Sci. Eng. A
, 341
(1
), pp. 307
–310
. 10.1016/S0921-5093(02)00199-517.
Gupta
, M. K.
, 2020
, “Friction Stir Process: a Green Fabrication Technique for Surface Composites—A Review Paper
,” SN Appl. Sci.
, 2
(4
), p. 532
. 10.1007/s42452-020-2330-218.
Liu
, Z. Y.
, Xiao
, B. L.
, Wang
, W. G.
, and Ma
, Z. Y.
, 2012
, “Singly Dispersed Carbon Nanotube/Aluminum Composites Fabricated by Powder Metallurgy Combined With Friction Stir Processing
,” Carbon
, 50
(5
), pp. 1843
–1852
. 10.1016/j.carbon.2011.12.03419.
Tewari
, A.
, Spowart
, J. E.
, Gokhale
, A. M.
, Mishra
, R. S.
, and Miracle
, D. B.
, 2006
, “Characterization of the Effects of Friction Stir Processing on Microstructural Changes in DRA Composites
,” Mater. Sci. Eng. A
, 428
(1
), pp. 80
–90
. 10.1016/j.msea.2006.04.10620.
Azimi-Roeen
, G.
, Kashani-Bozorg
, S. F.
, Nosko
, M.
, Orovcik
, L.
, and Lotfian
, S.
, 2020
, “Effect of Multi-Pass Friction Stir Processing on Textural Evolution and Grain Boundary Structure of Al–Fe3O4 System
,” J. Mater. Res. Technol.
, 9
(1
), pp. 1070
–1086
. 10.1016/j.jmrt.2019.10.07621.
Huang
, K.
, and Logé
, R. E.
, 2016
, “A Review of Dynamic Recrystallization Phenomena in Metallic Materials
,” Mater. Des.
, 111
, pp. 548
–574
. 10.1016/j.matdes.2016.09.01222.
Khodabakhshi
, F.
, Nosko
, M.
, and Gerlich
, A.
, 2018
, “Influence of CNTs Decomposition During Reactive Friction-Stir Processing of an Al–Mg Alloy on the Correlation Between Microstructural Characteristics and Microtextural Components
,” J. Microsc.
, 271
(2
), pp. 188
–206
. 10.1111/jmi.1270823.
Azimi-roeen
, G.
, Kashani-bozorg
, S. F.
, Nosko
, M.
, and Orovcik
, L.
, 2018
, “EBSD Investigation of Al/(Al13Fe4+ Al2O3) Nanocomposites Fabricated by Mechanical Milling and Friction Stir Processing
,” J. Microsc.
, 270
(1
), pp. 3
–16
. 10.1111/jmi.1264224.
Cao
, Y.
, Di
, H.
, Zhang
, J.
, Zhang
, J.
, Ma
, T.
, and Misra
, R. D. K.
, 2013
, “An Electron Backscattered Diffraction Study on the Dynamic Recrystallization Behavior of a Nickel–Chromium Alloy (800H) During hot Deformation
,” Mater. Sci. Eng. A
, 585
, pp. 71
–85
. 10.1016/j.msea.2013.07.03725.
David Raja Selvam
, J.
, and Dinaharan
, I.
, 2017
, “In Situ Formation of ZrB2 Particulates and Their Influence on Microstructure and Tensile Behavior of AA7075 Aluminum Matrix Composites
,” Eng. Sci. Technol.
, 20
(1
), pp. 187
–196
. 10.1016/j.jestch.2016.09.00626.
Muralidharan
, N.
, Chockalingam
, K.
, Dinaharan
, I.
, and Kalaiselvan
, K.
, 2018
, “Microstructure and Mechanical Behavior of AA2024 Aluminum Matrix Composites Reinforced With In Situ Synthesized ZrB2 Particles
,” J. Alloys Compd.
, 735
, pp. 2167
–2174
. 10.1016/j.jallcom.2017.11.37127.
Kumar
, N.
, Gautam
, R. K.
, and Mohan
, S.
, 2015
, “In-Situ Development of ZrB2 Particles and Their Effect on Microstructure and Mechanical Properties of AA5052 Metal-Matrix Composites
,” Mater. Des.
, 80
, pp. 129
–136
. 10.1016/j.matdes.2015.05.02028.
Kumar
, R. V.
, Keshavamurthy
, R.
, Perugu
, C. S.
, Koppad
, P. G.
, and Alipour
, M.
, 2018
, “Influence of Hot Rolling on Microstructure and Mechanical Behaviour of Al6061-ZrB2 in-Situ Metal Matrix Composites
,” Mater. Sci. Eng. A
, 738
, pp. 344
–352
. 10.1016/j.msea.2018.09.10429.
Ma
, Z. Y.
, 2008
, “Friction Stir Processing Technology: A Review
,” Metall. Mater. Trans. A
, 39
(3
), pp. 642
–658
. 10.1007/s11661-007-9459-030.
Hannard
, F.
, Castin
, S.
, Maire
, E.
, Mokso
, R.
, Pardoen
, T.
, and Simar
, A.
, 2017
, “Ductilization of Aluminium Alloy 6056 by Friction Stir Processing
,” Acta Mater.
, 130
, pp. 121
–136
. 10.1016/j.actamat.2017.01.04731.
Yuvaraj
, N.
, Aravindan
, S.
, and Vipin
, 2015
, “Fabrication of Al5083/B4C Surface Composite by Friction Stir Processing and its Tribological Characterization
,” J. Mater. Res. Technol.
, 4
(4
), pp. 398
–410
. 10.1016/j.jmrt.2015.02.00632.
Nene
, S. S.
, Liu
, K.
, Frank
, M.
, Mishra
, R. S.
, Brennan
, R. E.
, Cho
, K. C.
, Li
, Z.
, and Raabe
, D.
, 2017
, “Enhanced Strength and Ductility in a Friction Stir Processing Engineered Dual Phase High Entropy Alloy
,” Sci. Rep.
, 7
(1
), p. 16167
. 10.1038/s41598-017-16509-933.
Yang
, R.
, Zhang
, Z.
, Zhao
, Y.
, Chen
, G.
, Liu
, M.
, Jiao
, L.
, and Chen
, L.
, 2016
, “Microstructure-property Analysis of ZrB2/6061Al Hierarchical Nanocomposites Fabricated by Direct Melt Reaction
,” Mater. Charact.
, 112
, pp. 51
–59
. 10.1016/j.matchar.2015.12.01234.
Gupta
, R.
, Chaudhari
, G. P.
, and Daniel
, B. S. S.
, 2018
, “Strengthening Mechanisms in Ultrasonically Processed Aluminium Matrix Composite With in-Situ Al3Ti by Salt Addition
,” Composites, Part B
, 140
, pp. 27
–34
. 10.1016/j.compositesb.2017.12.00535.
Youssef
, Y. M.
, Dashwood
, R. J.
, and Lee
, P. D.
, 2005
, “Effect of Clustering on Particle Pushing and Solidification Behaviour in TiB2 Reinforced Aluminium PMMCs
,” Composites, Part A
, 36
(6
), pp. 747
–763
. 10.1016/j.compositesa.2004.10.02736.
Khan
, M. A.
, and Rohatgi
, P. K.
, 1993
, “A Numerical Study of Thermal Interaction of Solidification Fronts With Spherical Particles During Solidification of Metal-Matrix Composite Materials
,” Compos. Eng.
, 3
(10
), pp. 995
–1006
. 10.1016/0961-9526(93)90007-737.
Zhang
, Z.
, Yang
, R.
, Guo
, Y.
, Chen
, G.
, Lei
, Y.
, Cheng
, Y.
, and Yue
, Y.
, 2017
, “Microstructural Evolution and Mechanical Properties of ZrB2/6061Al Nanocomposites Processed by Multi-Pass Friction Stir Processing
,” Mater. Sci. Eng. A
, 689
, pp. 411
–418
. 10.1016/j.msea.2017.02.08338.
Dinaharan
, I.
, 2016
, “Influence of Ceramic Particulate Type on Microstructure and Tensile Strength of Aluminum Matrix Composites Produced Using Friction Stir Processing
,” J. Asian Ceram. Soc.
, 4
(2
), pp. 209
–218
. 10.1016/j.jascer.2016.04.00239.
Rossi
, P.
, Suarez
, S.
, Soldera
, F.
, and Mücklich
, F.
, 2015
, “Quantitative Assessment of the Reinforcement Distribution Homogeneity in CNT/Metal Composites
,” Adv. Eng. Mater.
, 17
(7
), pp. 1017
–1021
. 10.1002/adem.20140035240.
Aristizabal
, K.
, Katzensteiner
, A.
, Bachmaier
, A.
, Mücklich
, F.
, and Suárez
, S.
, 2018
, “On the Reinforcement Homogenization in CNT/Metal Matrix Composites During Severe Plastic Deformation
,” Mater. Charact.
, 136
, pp. 375
–381
. 10.1016/j.matchar.2018.01.00741.
Rao
, A. G.
, Ravi
, K. R.
, Ramakrishnarao
, B.
, Deshmukh
, V. P.
, Sharma
, A.
, Prabhu
, N.
, and Kashyap
, B. P.
, 2013
, “Recrystallization Phenomena During Friction Stir Processing of Hypereutectic Aluminum-Silicon Alloy
,” Metall. Mater. Trans. A
, 44
(3
), pp. 1519
–1529
. 10.1007/s11661-012-1489-642.
Yadav
, D.
, and Bauri
, R.
, 2011
, “Processing, Microstructure and Mechanical Properties of Nickel Particles Embedded Aluminium Matrix Composite
,” Mater. Sci. Eng. A
, 528
(3
), pp. 1326
–1333
. 10.1016/j.msea.2010.10.03543.
Huang
, G.
, Wu
, J.
, Hou
, W.
, and Shen
, Y.
, 2018
, “Microstructure, Mechanical Properties and Strengthening Mechanism of Titanium Particle Reinforced Aluminum Matrix Composites Produced by Submerged Friction Stir Processing
,” Mater. Sci. Eng. A
, 734
, pp. 353
–363
. 10.1016/j.msea.2018.08.01544.
Ajay Kumar
, P.
, Yadav
, D.
, Perugu
, C. S.
, and and Kailas
, S. V.
, 2017
, “Influence of Particulate Reinforcement on Microstructure Evolution and Tensile Properties of In-Situ Polymer Derived MMC by Friction Stir Processing
,” Mater. Des.
, 113
, pp. 99
–108
. 10.1016/j.matdes.2016.09.10145.
Kumar
, H.
, Prasad
, R.
, Kumar
, P.
, Tewari
, S. P.
, and Singh
, J. K.
, 2020
, “Mechanical and Tribological Characterization of Industrial Wastes Reinforced Aluminum Alloy Composites Fabricated via Friction Stir Processing
,” J. Alloys Compd.
, 831
, p. 154832
. 10.1016/j.jallcom.2020.15483246.
Dinaharan
, I.
, Saravanakumar
, S.
, Kalaiselvan
, K.
, and Gopalakrishnan
, S.
, 2017
, “Microstructure and Sliding Wear Characterization of Cu/TiB2 Copper Matrix Composites Fabricated via Friction Stir Processing
,” J. Asian Ceram. Soc.
, 5
(3
), pp. 295
–303
. 10.1016/j.jascer.2017.06.00247.
Kumar
, H.
, Prasad
, R.
, and Kumar
, P.
, 2020
, “Effect of Multi-Groove Reinforcement Strategy on Cu/SiC Surface Composite Fabricated by Friction Stir Processing
,” Mater. Chem. Phys.
, 256
, p. 123720
. 10.1016/j.matchemphys.2020.12372048.
Huang
, G.
, and Shen
, Y.
, 2017
, “The Effects of Processing Environments on the Microstructure and Mechanical Properties of the Ti/5083Al Composites Produced by Friction Stir Processing
,” J. Manuf. Process.
, 30
, pp. 361
–373
. 10.1016/j.jmapro.2017.10.00749.
Schneider
, J. A.
, and Nunes
, A. C.
, 2004
, “Characterization of Plastic Flow and Resulting Microtextures in a Friction Stir Weld
,” Metall. Mater. Trans. B
, 35
(4
), pp. 777
–783
. 10.1007/s11663-004-0018-450.
Tongne
, A.
, Desrayaud
, C.
, Jahazi
, M.
, and Feulvarch
, E.
, 2017
, “On Material Flow in Friction Stir Welded Al Alloys
,” J. Mater. Process. Technol.
, 239
, pp. 284
–296
. 10.1016/j.jmatprotec.2016.08.03051.
Schneider
, J.
, Beshears
, R.
, and Nunes
, A. C.
, 2006
, “Interfacial Sticking and Slipping in the Friction Stir Welding Process
,” Mater. Sci. Eng. A
, 435–436
, pp. 297
–304
. 10.1016/j.msea.2006.07.08252.
Raviathul Basariya
, M.
, Srivastava
, V. C.
, and and Mukhopadhyay
, N. K.
, 2014
, “Microstructural Characteristics and Mechanical Properties of Carbon Nanotube Reinforced Aluminum Alloy Composites Produced by Ball Milling
,” Mater. Des.
, 64
, pp. 542
–549
. 10.1016/j.matdes.2014.08.01953.
Wu
, B. B.
, Wang
, Z. Q.
, Wang
, X. L.
, Zhao
, J. X.
, Shang
, C. J.
, and Misra
, R. D. K.
, 2019
, “Relationship Between High Angle Grain Boundaries and Hardness After γ→α Transformation
,” Mater. Sci. Technol.
, 35
(15
), pp. 1803
–1814
. 10.1080/02670836.2019.164793654.
Guha
, R. D.
, Sharma
, A. J.
, Diwan
, P.
, and Khanikar
, P.
, 2017
, “Effect of Grain Orientation on High Strain-Rate Plastic Deformation
,” Procedia Eng.
, 173
, pp. 1048
–1055
. 10.1016/j.proeng.2016.12.18455.
Nallusamy
, M.
, Sundaram
, S.
, and Kalaiselvan
, K.
, 2019
, “Fabrication, Characterization and Analysis of Improvements in Mechanical Properties of AA7075/ZrB2 in-Situ Composites
,” Measurement
, 136
, pp. 356
–366
. 10.1016/j.measurement.2018.12.11056.
Prasad
, R.
, Tewari
, S.
, and Singh
, J.
, 2019
, “Effect of Multi-Pass Friction Stir Processing on Microstructural, Mechanical and Tribological Behaviour of as-Cast Al–Zn–Mg–Cu Alloy
,” Mater. Res. Express
, 6
(9
), p. 096579
. 10.1088/2053-1591/ab308c57.
Waghmare
, A. K.
, and Sahoo
, P.
, 2015
, “Adhesive Friction at the Contact Between Rough Surfaces Using n-Point Asperity Model
,” Eng. Sci. Technol.
, 18
(3
), pp. 463
–474
. 10.1016/j.jestch.2015.03.00658.
Konopka
, K.
, Boczkowska
, A.
, Batorski
, K.
, Szafran
, M.
, and Kurzydłowski
, K. J.
, 2004
, “Microstructure and Properties of Novel Ceramic–Polymer Composites
,” Mater. Lett.
, 58
(30
), pp. 3857
–3862
. 10.1016/j.matlet.2004.07.02559.
Choi
, S. R.
, and Bansal
, N. P.
, 2005
, “Mechanical Behavior of Zirconia/Alumina Composites
,” Ceram. Int.
, 31
(1
), pp. 39
–46
. 10.1016/j.ceramint.2004.03.03260.
Barmouz
, M.
, Besharati Givi
, M. K.
, and Seyfi
, J.
, 2011
, “On the Role of Processing Parameters in Producing Cu/SiC Metal Matrix Composites via Friction Stir Processing: Investigating Microstructure, Microhardness, Wear and Tensile Behavior
,” Mater. Charact.
, 62
(1
), pp. 108
–117
. 10.1016/j.matchar.2010.11.00561.
Zahmatkesh
, B.
, Enayati
, M. H.
, and Karimzadeh
, F.
, 2010
, “Tribological and Microstructural Evaluation of Friction Stir Processed Al2024 Alloy
,” Mater. Des.
, 31
(10
), pp. 4891
–4896
. 10.1016/j.matdes.2010.04.05462.
Bowden
, F. P.
, and Tabor
, D.
, 2001
, The Friction and Lubrication of Solids
, Oxford University Press
, Oxford, UK
.63.
Kumar
, A.
, Staedler
, T.
, and Jiang
, X.
, 2013
, “Effect of Normal Load and Roughness on the Nanoscale Friction Coefficient in the Elastic and Plastic Contact Regime
,” Beilstein J. Nanotechnol.
, 4
(1
), pp. 66
–71
. 10.3762/bjnano.4.764.
Neale
, M. J.
, 1995
, “Nature of Surfaces and Contact,” Tribology Handbook
, 2nd ed., M. J.
Neale
, ed., Butterworth-Heinemann
, Oxford
, pp. E1.1
–E1.3
.65.
Hutchings
, I.
, and Shipway
, P.
, 2017
, Tribology: Friction and Wear of Engineering Materials
, Butterworth-Heinemann
, Oxford, UK
.66.
Menezes
, P. L.
, Kishore
, Kailas
, S. V.
, and Lovell
, M. R.
, 2011
, “Role of Surface Texture, Roughness, and Hardness on Friction During Unidirectional Sliding
,” Tribol. Lett.
, 41
(1
), pp. 1
–15
. 10.1007/s11249-010-9676-367.
Liou
, J. W.
, Chen
, L. H.
, and Lui
, T. S.
, 1995
, “The Concept of Effective Hardness in the Abrasion of Coarse two-Phase Materials with Hard Second-Phase Particles
,” J. Mater. Sci.
, 30
(1
), pp. 258
–262
. 10.1007/BF0035215968.
Feng
, C.
, Wang
, Y.
, Chen
, W.
, Zhang
, L.
, and Zhou
, K.
, 2017
, “The Mechanical Mixed Layer and Its Role in Cu-15Ni-8Sn/Graphite Composites
,” Tribol. Trans.
, 60
(1
), pp. 135
–145
. 10.1080/10402004.2016.115262169.
Daoud
, A.
, and Abou El-khair
, M. T.
, 2010
, “Wear and Friction Behavior of Sand Cast Brake Rotor Made of A359–20vol% SiC Particle Composites Sliding Against Automobile Friction Material
,” Tribol. Int.
, 43
(3
), pp. 544
–553
. 10.1016/j.triboint.2009.09.00370.
Straffelini
, G.
, Pellizzari
, M.
, and Molinari
, A.
, 2004
, “Influence of Load and Temperature on the dry Sliding Behaviour of Al-Based Metal-Matrix-Composites Against Friction Material
,” Wear
, 256
(7
), pp. 754
–763
. 10.1016/S0043-1648(03)00529-571.
Sudarshan
, and Surappa
, M. K.
, 2008
, “Dry Sliding Wear of fly ash Particle Reinforced A356 Al Composites
,” Wear
, 265
(3
), pp. 349
–360
. 10.1016/j.wear.2007.11.00972.
Samanta
, P. N.
, and Leszczynski
, J.
, 2018
, “High-temperature Thermoelectric Transport Behavior of the Al/γ-Al 2 O 3 Interface: Impact of Electron and Phonon Scattering at Nanoscale Metal–Ceramic Contacts
,” Phys. Chem. Chem. Phys.
, 20
(21
), pp. 14513
–14524
. 10.1039/C8CP01374H73.
Singh
, J.
, and Alpas
, A. T.
, 1996
, “High-temperature Wear and Deformation Processes in Metal Matrix Composites
,” Metall. Mater. Trans. A
, 27
(10
), pp. 3135
–3148
. 10.1007/BF0266386474.
Zhang
, J.
, and Alpas
, A. T.
, 1997
, “Transition Between Mild and Severe Wear in Aluminium Alloys
,” Acta Mater.
, 45
(2
), pp. 513
–528
. 10.1016/S1359-6454(96)00191-7Copyright © 2020 by ASME
You do not currently have access to this content.
