Corrosion fatigue crack propagation tests were conducted on a medium-sulfur ASTM A508-2 forging steel overlaid with weld-deposited alloy EN82H cladding. The specimens featured semi-elliptical surface cracks penetrating approximately 6.3 mm of cladding into the underlying steel. The initial crack sizes were relatively large with surface lengths of 30.3–38.3 mm, and depths of 13.1–16.8 mm. The experiments were conducted in a quasi-stagnant low-oxygen (O2 < 10ppb) aqueous environment at 243°C, under loading conditions (ΔK, R, and cyclic frequency) conducive to environmentally assisted cracking (EAC) in higher-sulfur steels under quasi-stagnant conditions. Earlier experiments on unclad compact tension specimens of this heat of steel did not exhibit EAC, and the present experiments on semi-elliptical surface cracks penetrating cladding also did not exhibit EAC.

Issue Section:
Research Papers
Topics:
Alloys, Corrosion, Fatigue cracks, Forging, Steel, Sulfur, Cladding systems (Building), Surface cracks, ASTM International, Fracture (Materials), Fracture (Process), Heat, Oxygen, Tension
1.
Andresen
P. L.
, and
Young
L. M.
,
1995
, “
Crack Tip Microsampling and Growth Rate Measurements in Low Alloy Steel in High Temperature Water
,”
Corrosion
, Vol.
51
, No.
3
, pp.
223
–
233
.
2.
Auten, T. A., Hayden, S. Z., and Emanuelson, R. H., 1993, “Fatigue Crack Growth Rate Studies of Medium Sulfur Low Alloy Steels Tested in High Temperature Water,” Proceedings, Sixth International Symposium on Environmental Degradation of Materials in Nuclear Power Systems—Water Reactors, TMS-AIME, pp. 35–41
3.
Bazˇant
Z. P.
and
Estenssoro
L. F.
,
1979
, “
Surface Singularity and Crack Propagation
,”
International Journal of Solids and Structures
, Vol.
15
, No.
5
, pp.
405
–
426
.
4.
Bernard
J. L.
,
Vagner
J.
,
Pellissier-Tanon
A.
, and
Fauer
F.
,
1992
, “
Effect of Residual Stresses and Complex Loadings on the Fatigue Behavior of Underclad Cracks
,”
Nuclear Engineering and Design
, Vol.
133
, No.
1
, pp.
3
–
15
.
5.
Bramwell, I. L., Tice, D. R., Worswick, D., and Heys, G. B., 1995, “The Effect of Stainless Steel Overlay Cladding on Corrosion Fatigue Crack Propagation in a Pressure Vessel Steel in PWR Primary Coolant,” Proceedings, Seventh International Symposium on Environmental Degradation of Materials in Nuclear Power Systems—Water Reactors, Vol. 2, NACE, pp. 1157–1168.
6.
Crouch
B. A.
,
1991
, “
The Effect of Crack Front Curvature and Side-Grooving on Three Point Bend Specimen Fracture Toughness Measurement
,”
International Journal of Fracture
, Vol.
52
, No.
4
, pp.
275
–
292
.
7.
Eason
E. D.
,
Andrew
S. P.
,
Warmbrodt
S. B.
,
Nelson
E. E.
, and
Gilman
J. D.
,
1989
, “
Analysis of Pressure Vessel Steel Fatigue Tests in Air
,”
Nuclear Engineering and Design
, Vol.
115
, No.
1
, pp.
23
–
30
.
8.
James
L. A.
, and
Wilson
W. K.
,
1994
a, “
Development of a Surface-Cracked Specimen
,”
Theoretical and Applied Fracture Mechanics
, Vol.
20
, No.
2
, pp.
115
–
121
.
9.
James
L. A.
,
1994
b, “
The Effect of Temperature and Cyclic Frequency Upon Fatigue Crack Growth Behavior of Several Steels in an Elevated Temperature Aqueous Environment
,”
ASME JOURNAL OF PRESSURE VESSEL TECHNOLOGY
, Vol.
116
, pp.
122
–
127
.
10.
James
L. A.
,
Wire
G. L.
, and
Cullen
W. H.
,
1995
a, “
The Effect of Water Flow Rate Upon the Environmentally-Assisted Cracking Response of a Low-Alloy Steel
,”
ASME JOURNAL OF PRESSURE VESSEL TECHNOLOGY
, Vol.
117
, pp.
238
–
244
.
11.
James
L. A.
, and
Mills
W. J.
,
1995
b, “
Fatigue Crack Propagation Behavior of Wrought Alloy 600 and Weld-Deposited EN82H in an Elevated Temperature Aqueous Environment
,” Service Experience, Structural Integrity, Severe Accidents, and Erosion in Nuclear and Fossil Plants,
ASME PVP
-Vol.
303
, pp.
21
–
36
.
12.
James
L. A.
,
Lee
H. B.
, and
Wire
G. L.
,
1997
, “
The Effect of Water Flow Rate Upon the Environmentally Assisted Cracking Response of a Low-Alloy Steel: Experimental Results Plus Modeling
,”
ASME JOURNAL OF PRESSURE VESSEL TECHNOLOGY
, Vol.
119
, Feb., pp.
83
–
90
.
13.
Kan
R.
, and
Blackburn
W. S.
,
1992
, “
Effect of Crack Front Non-Linearity on Results From Compact Tension Tests
,”
International Journal of Fracture
, Vol.
55
, No.
3
pp.
285
–
292
.
14.
Kondo, T., Kikuyama, T., Nakajima, H., and Shindo, M., 1972, “Fatigue of Low-Alloy Steels in Aqueous Environment at Elevated Temperatures,” Mechanical Behavior of Materials, Proceedings, International Conference on Mechanical Behavior of Materials, Vol. 3, pp. 319–327.
15.
Lin
K. Y.
, and
Mar
J. W.
,
1976
, “
Finite Element Analysis of Stress Intensity Factors at a Bimaterial Interface
,”
International Journal of Fracture
, Vol.
12
, No.
4
, pp.
521
–
531
.
16.
Luchi
M. L.
, and
Rizzuti
S.
,
1987
, “
Boundary Element Analysis of CT Specimens With Straight and Curved Crack Fronts
,”
International Journal of Fracture
, Vol.
34
, No.
1
, pp
23
–
40
.
17.
Macdonald
D. D.
,
Scott
A. C.
, and
Wentrcek
P.
,
1979
, “
Silver-Silver Chloride Thermocells and Thermal Liquid Junction Potentials for Potassium Chloride Solution at Elevated Temperatures
,”
Journal of the Electrochemical Society
, Vol.
126
, No.
9
, pp.
1618
–
1624
.
18.
Newman, J. C., and Raju, I. S., 1984, “Stress Intensity Factor Equations for Cracks in Three-Dimensional Finite Bodies Subjected to Tension and Bending Loads,” NASA Technical Memorandum 85793
19.
Pedron
J. P.
,
Diboine
A.
, and
Pineau
A.
,
1984
, “
Fatigue Crack Growth Rate Behavior of Stainless Steel Claddings in Air and Under Vacuum at 300°C
,”
Fatigue of Engineering Materials and Structures
, Vol.
7
, No.
2
, pp.
137
–
143
.
20.
Pook
L. P.
,
1994
, “
Some Implications of Corner Point Singularities
,”
Engineering Fracture Mechanics
, Vol.
48
, No.
3
, pp.
367
–
378
.
21.
Rahka, K., Ha¨nninen, H., Saario, T., To¨rro¨nen, K., and Ahlstrand, R., 1990, “Fatigue Crack Propagation Through Welded Cladding Into Base Metal in LWR-Pressure Vessel Materials,” NUREG/CP-0112, Vol. 1, pp. 253–262
22.
Romeo
A.
, and
Ballarini
R.
,
1995
, “
A Crack Very Close to a Bimaterial Interface
,”
ASME Journal of Applied Mechanics
, Vol.
62
, pp.
614
–
619
.
23.
Ruther, W. E., Shack, W. J., Chung, H. M., Kassner, T. F., and Soppet, W. K., 1991, “Environmentally Assisted Cracking in Light Water Reactors,” NUREG/ CR-4667, Vol. 10.
24.
Shoji
T.
,
Takahashi
H.
,
Suzuki
M.
, and
Kondo
T.
,
1981
, “
A New Parameter for Characterizing Corrosion Fatigue Crack Growth
,”
ASME Journal of Engineering Materials and Technology
, Vol.
103
, pp.
298
–
304
.
25.
Shoji
T.
,
Takahaski
H.
,
Nakajima
H.
, and
Kondo
T.
,
1983
, “
Role of Loading Variables in Environment Enhanced Crack Growth for Water-Cooled Nuclear Reactor Pressure Vessel Steels
,”
NUREG/CP-0044
, Vol.
2
, pp.
143
–
171
.
26.
Sih
G. C.
, and
Lee
Y. D.
,
1989
, “
Review of Triaxial Border Stress and Energy Behavior
,”
Theoretical and Applied Fracture Mechanics
, Vol.
12
, No.
1
, pp.
1
–
17
.
27.
Tada, H., 1985, The Stress Analysis of Cracks Handbook, Second Edition, Paris Productions Inc., St. Louis
28.
Towers
O. L.
, and
Smith
A. P.
,
1984
, “
Stress Intensity Factors for Curved Crack Fronts in Compact Tension Specimens
,”
International Journal of Fracture
, Vol.
25
, No.
2
, pp.
R43–R48
R43–R48
.
29.
Yamamoto
Y.
,
Sumi
Y.
,
Shimoyama
T.
, and
Funada
T.
,
1987
, “
On Thumb-Nail Pattern of Fatigue Crack Front Observed in Standard Compact Tension Specimen
,”
International Journal of Fracture
, Vol.
34
, No.
2
, pp.
149
–
157
.
This content is only available via PDF.
Copyright © 1997
 by The American Society of Mechanical Engineers
You do not currently have access to this content.