This paper presents a technique, based on Monte-Carlo simulations, of utilizing a screw over its yield point in a controlled fashion, even under simple tightening conditions. The simulations consider the probabilistic nature of different variables necessary to calculate screwed joints. The proposed torque and angle controlled tightening technique can be used in assembly plants as well as in small workshops. The technique predicts permanent elongation, maximum tightening angle, final torque and preload after tightening. Further, a recommendation on the minimum and maximum snug torques prior to application of the angle over the yield point of a screw is also presented.
Issue Section:
Technical Papers
1.
Okubo, T., Tanaka, S., and Gorumaru, K., 1984, “Reliability Evaluation of Bolts Tightened in Plastic Region and Their Application to Diesel Engines,” SAE Paper 840505.
2.
Blatt 1, 2001, Systematische Berechnung hochbeanspruchter Schraubenverbindungen Zylindrische Einschraubenverbindungen, VDI 2230, VDI-Verlag, Du¨sseldorf.
3.
Junker
, G. H.
, 1970
, “Reihenuntersuchungen von Schraubenverbindungen mit Motorischen Schraubern
,” Draht-Welt, Fachbeilage Schrauben Muttern Formteile
, 56
, Heft 3
Heft 3
.4.
Monaghan
, J. M.
, 1991
, “Influence of Lubrication on the Design of Yield Tightened Joints
,” J. Strain Anal. Eng. Des.
, , 26
(2
), pp. 123
–132
.5.
Boys
, J. T.
, and Wallace
, P. W.
, 1977
, “Design and Performance of an Automatic Control System for Fastener Tightening
,” Proc. Inst. Mech. Eng.
, 191
, pp. 371
–380
.6.
Finkelston
, R. J.
, and Kull
, F. R.
, 1978
, “Preloading for Optimum Bolt Efficiency
,” Assembly Engineering
, 17
(8
), pp. 24
–28
.7.
Junker
, G. H.
, and Wallace
, P. W.
, 1984
, “The Bolted Joint: Economy of Design Through Improved Analysis and Assembly Methods
,” Proc. Inst. Mech. Eng.
, 198B
(14
), pp. 255
–266
.8.
Bickford. J. H., 1990, An Introduction to the Design and Behavior of Bolted Joints, 2nd Edition, Marcel Dekker, Inc., New York.
9.
Edwards, K. J., and McKee, R. B., 1991, Fundamentals of Mechanical Component Design, 1st Edition, McGraw-Hill, New York.
10.
Research Council on Structural Connections., 2000, Specification for Structural Joints Using ASTM A325 or A490 Bolts.
11.
Frincke
, M. H.
, 1958
, “Turn-of-nut Method for Tensioning Bolts
,” Civ. Eng.
, 28
, pp. 63
–64
.12.
Wallace
, P. W.
, 1975
, “Joint Control System
,” Engineering Materials and Design
, 19
, pp. 35
–38
.13.
Shigley, J. E., and Mischke, C. R., 1989, Mechanical Engineering Design, 5th Edition, McGraw-Hill, New York.
14.
Humble
, P. A.
, 1986
, “Better Control of Bolt Tension
,” Engineering Designer
, pp.
18
–21
.15.
Boys
, J. T.
, and Tambini
, A.
, 1981
, “Tightening Methods for Fasteners
,” Engineering
, 221
, pp. I–IV
I–IV
.16.
ISO 898-1, 1988, “Mechanical Properties of Fasteners,” Part 1, ISO Central Secretariat, Gene`ve, Switzerland.
17.
Toth, G. R., “Torque and Angle Controlled Tightening Over the Yield Point,” Internal report, Dept. of Machine and Vehicle Systems, Chalmers University of Technology, SE-412 96 Go¨teborg, Sweden.
18.
Toth
, G. R.
, 2003
“Controlled Tightening Over the Yield Point of a Screw—Based on Taylor’s Series Expansions
,” ASME J. Pressure Vessel Technol.
, 125
(4
), pp. 460
–466
.Copyright © 2004
by ASME
You do not currently have access to this content.
