Effect of fiber volume fraction on occurrence, morphology, and spatial distribution of microvoids in resin transfer molded E-glass/epoxy composites is investigated. Three disk-shaped center-gated composite parts containing 8, 12, and 16 layers of randomly-oriented, E-glass fiber perform are molded, yielding 13.5%, 20.5%, and 27.5% fiber volume fractions. Voids are evaluated by microscopic image analysis of the samples obtained along the radius of these disk-shaped composites. The number of voids is found to decrease moderately with increasing fiber content. Void areal density decreased from to as fiber content is increased from 13.5% to 27.5%. Similarly, void volume fraction decreased from 3.1% to 2.5%. Increasing fiber volume fraction from 13.5% to 27.5% is found to lower the contribution of irregularly-shaped voids from 40% of total voids down to 22.4%. Along the radial direction, combined effects of void formation by mechanical entrapment and void mobility are shown to yield a spatially complex void distribution. However, increasing fiber content is observed to affect the void formation mechanisms as more voids are able to move toward the exit vents during molding. These findings are believed to be applicable not only to resin transfer molding but generally to liquid composite molding processes.
Skip Nav Destination
e-mail: altan@ou.edu
Article navigation
April 2009
Research Papers
Effect of Fiber Content on Void Morphology in Resin Transfer Molded E-Glass/Epoxy Composites
Youssef K. Hamidi,
Youssef K. Hamidi
Ecole Nationale des Science Appliquées Safi,
Université Cadi Ayyad
, BP 63, 46000 Safi, Morocco
Search for other works by this author on:
Sudha Dharmavaram,
Sudha Dharmavaram
School of Aerospace and Mechanical Engineering,
University of Oklahoma
, Norman, OK 73019
Search for other works by this author on:
Levent Aktas,
Levent Aktas
School of Aerospace and Mechanical Engineering,
University of Oklahoma
, Norman, OK 73019
Search for other works by this author on:
M. Cengiz Altan
M. Cengiz Altan
School of Aerospace and Mechanical Engineering,
e-mail: altan@ou.edu
University of Oklahoma
, Norman, OK 73019
Search for other works by this author on:
Youssef K. Hamidi
Ecole Nationale des Science Appliquées Safi,
Université Cadi Ayyad
, BP 63, 46000 Safi, Morocco
Sudha Dharmavaram
School of Aerospace and Mechanical Engineering,
University of Oklahoma
, Norman, OK 73019
Levent Aktas
School of Aerospace and Mechanical Engineering,
University of Oklahoma
, Norman, OK 73019
M. Cengiz Altan
School of Aerospace and Mechanical Engineering,
University of Oklahoma
, Norman, OK 73019e-mail: altan@ou.edu
J. Eng. Mater. Technol. Apr 2009, 131(2): 021014 (11 pages)
Published Online: March 9, 2009
Article history
Received:
May 30, 2005
Revised:
October 13, 2008
Published:
March 9, 2009
Citation
Hamidi, Y. K., Dharmavaram, S., Aktas, L., and Altan, M. C. (March 9, 2009). "Effect of Fiber Content on Void Morphology in Resin Transfer Molded E-Glass/Epoxy Composites." ASME. J. Eng. Mater. Technol. April 2009; 131(2): 021014. https://doi.org/10.1115/1.3030944
Download citation file:
Get Email Alerts
Creep Performance Study of Inconel 740H Weldment Based on Microstructural Deformation Mechanisms
J. Eng. Mater. Technol (October 2024)
Effect of Heat Treatment on Fatigue Performance of 316L Stainless Steel Fabricated by Laser Powder Bed Fusion
J. Eng. Mater. Technol (October 2024)
Design and Development of Novel Lattice Structures for Optimum Energy Absorption
J. Eng. Mater. Technol (July 2024)
Related Articles
Post-Curing Effects on Marine VARTM FRP Composite Material Properties for Test and Implementation
J. Eng. Mater. Technol (January,2006)
Manufacturing Modeling of Three-Dimensional Resin Injection Pultrusion Process Control Parameters for Polyester/Glass Rovings Composites
J. Manuf. Sci. Eng (February,2007)
Flow and Mold Filling Modeling and Simulation to Enhance Resin Transfer Molding Processes
J. Eng. Mater. Technol (July,2008)
Related Proceedings Papers
Related Chapters
Fatigue Failure Mechanisms in a Unidirectionally Reinforced Composite Material
Fatigue of Composite Materials
Stiffening Mechanisms
Introduction to Plastics Engineering
Research on Strengthening Mechanism of Plant Root in Slope Protection
Geological Engineering: Proceedings of the 1 st International Conference (ICGE 2007)