A new model for springback, based on isotropic and kinematic hardening models, the Mroz multiple surfaces model, and observations from experimental data, is proposed in this paper. In this model, a material parameter (CM), which is significant after reverse yielding, is suggested to handle the Bauschinger effect. A simple, low-cost, multiple-bending experiment has been developed to determine CM for aluminum alloys AA6022-T4 and AA6111-T4. The new model fits available experimental results better than the isotropic and kinematic hardening models and the Mroz multiple surfaces model.
Issue Section:
Research Papers
1.
Gau
, J.-T.
, and Kinzel
, G. L.
, 2001, “An Experimental Investigation of the Influence of the Bauschinger Effect on Springback Predictions
,” J. Mater. Process. Technol.
0924-0136, 108
, pp. 369
–375
.2.
Abel
, A.
, and Muir
, H.
, 1972, “The Bauschinger Effect and Discontinuous Yielding
,” Philos. Mag.
0031-8086, 26
, pp. 489
–504
.3.
Sowerby
, R.
, and Uko
, D. K.
, 1979, “A Review of Certain Aspects of the Bauschinger effect in Metals
,” Mater. Sci. Eng.
0025-5416, 41
, pp. 43
–58
.4.
Bate
, P. S.
, and Wilson
, D. V.
, 1986, “Analysis of The Bauschinger Effect
,” Acta Metall.
0001-6160, 34
(6
), pp. 1097
–1105
.5.
Fenoglietto
, F.
, Morestin
, F.
, Boivin
, M.
, and Deng
, X.
, 1995, “Springback Analysis in Orthotrpic Sheet Metal Forming With An Elasto Plastic Formulation Using A Kinematic Hardening Model
,” in Simulation of Materials and Applications
, Shen
and Dawson
(eds.) ISBN 90 5410 5534, AaBalkema, Boston, pp. 699
–704
.6.
Pourboghrat
, F.
, and Chu
, E.
, 1995, “Springback in Plane Strain Stretch/Draw Sheet Forming
,” Int. J. Mech. Sci.
0020-7403, 36
(3
), pp. 327
–341
.7.
Kuwabara
, T.
, Takahashi
, S.
, Akiyama
, K.
, and Ito
, K.
, 1996, “Springback Analysis of Sheet Metal subjected to Bending-Unbending under Tension (parts I and II)
,” Adv. Technol. Plasticity
, Proc. 5th ICTP, T.
Altan
, ed., pp. 743
–750
.8.
Morestin
, F.
, Boivin
, M.
, and Silva
, C.
, 1996, “Elasto Plastic Formulation Using A Kinematic Hardening Model For Springback Analysis In Sheet Metal Forming
,” J. Mater. Process. Technol.
0924-0136, 56
, pp. 619
–630
.9.
Zhang
, Z. T.
, and Hu
, S. J.
, 1998, “Stress and Residual Stress Distributions in Plane Strain Bending
,” Int. J. Mech. Sci.
0020-7403, 40
(6
), pp. 533
–553
.10.
Gau
, J.-T.
, and Kinzel
, G. L.
, 2001, “A New Model for Springback Prediction in Which the Bauschinger Effect Is Considered
,” Int. J. Mech. Sci.
0020-7403, 43
, pp. 1813
–1832
.11.
Mroz
, Z.
, 1967, “On The Description Of Anisotropic Work Hardening
,” J. Mech. Phys. Solids
0022-5096, 15
, pp. 163
–175
.12.
Mroz
, Z.
, 1969, “An Attempt To Describe The Behavior Of Metal Under Cyclic Loads Using A More General Work Harding Model
,” Acta Mech.
0001-5970, 7
, pp. 199
–212
.13.
Chu
, C. C.
, 1984, “A Three-dimensional Model of Anisotropic Hardening in Metals and Its Application to the Analysis of Sheet Metal Formability
,” Int. J. Mech. Phys. Solids Mech. Sci.
, 32
(3
), pp. 197
–212
.14.
Hill
, R.
, 1950, The Mathematical Theory of Plasticity
, Oxford University Press
, London.15.
Hodge
, P.
, 1957, ”Discussion of the Prager Hardening Law
,” ASME J. Appl. Mech.
0021-8936, 24
, pp. 482
–484
.16.
Carden
, W. D.
, 1997, “Springback After Drawing and Bending of Metal Sheets
,” M.S. thesis, The Ohio State University.Copyright © 2005
by American Society of Mechanical Engineers
You do not currently have access to this content.
