This study of cavitation inception from a solid surface includes the presentation of an empirical model for the nuclei, a completely new design for experimental test equipment, a rigorous analysis of liquid conditions within the test section, and quantitative test data. The results prove that it is possible to reduce the effective size of cavitation nuclei, thereby making the interface more resistant to cavitation. The empirical model for cavitation nuclei provides the mechanism for bubble formation from gas-filled, submicroscopic crevices in a solid surface. The size of these nuclei may be reduced by forcing the liquid into these crevices. If the liquid-solid interface is hydrophilic, the pressure treatment is permanent, but the liquid will pull out of a hydrophobic interface thus providing only a temporary reduction of nuclei dimensions. The newly designed experimental equipment for cavitation inception studies has been demonstrated to produce cavitation under controlled conditions. The test section resembles a 180-deg journal bearing constructed in three slices. The middle slice is slid away from the journal to produce a diverging wedge which induces a tensile stress in the liquid. The inception stage of cavitation is detected by an acoustical probe. The temperature and pressure distributions in the thin film are calculated numerically by successively solving the energy and generalized Reynolds equations. A strongly implicit iteration algorithm is employed to solve the large set of simultaneous algebraic equations resulting from placing the nonlinear elliptic partial differential equations in finite difference form. Experimental data from test runs with petroleum oil, glycerin, and a glycerin-soap mixture showed that stress required for inception of cavitation could be determined with a repeatability of ±1.4 × 104 Pa (±2 psi). A linear relationship was experimentally determined to exist between the magnitude of pressure forcing oil into the crevices of a steel surface and a capacity of the oil-steel interface to withstand a tensile stress.
Skip Nav Destination
Article navigation
February 1976
This article was originally published in
Journal of Engineering for Industry
Research Papers
Inception of Cavitation From a Solid Surface
G. E. Miller,
G. E. Miller
Engineering R&D Division, E. I. du Pont de Nemours and Co., Wilmington, Dela.
Search for other works by this author on:
H. G. Rylander
H. G. Rylander
Mechanical Engineering, The University of Texas at Austin, Austin, Texas
Search for other works by this author on:
G. E. Miller
Engineering R&D Division, E. I. du Pont de Nemours and Co., Wilmington, Dela.
H. G. Rylander
Mechanical Engineering, The University of Texas at Austin, Austin, Texas
J. Eng. Ind. Feb 1976, 98(1): 145-152
Published Online: February 1, 1976
Article history
Online:
July 15, 2010
Connected Content
Citation
Miller, G. E., and Rylander, H. G. (February 1, 1976). "Inception of Cavitation From a Solid Surface." ASME. J. Eng. Ind. February 1976; 98(1): 145–152. https://doi.org/10.1115/1.3438808
Download citation file:
10
Views
Get Email Alerts
Cited By
Related Articles
Cavitation Properties of Oils Under Dynamic Stressing by Tension
J. Fluids Eng (March,2005)
Operation Parameters' Effect on Gaseous Bubbles in Lubricant of Groove Textured Journal Bearing
J. Tribol (September,2017)
Experimental Validation of the Simulated Steady-State Behavior of Porous Journal Bearings
J. Tribol (July,2016)
On Olsson's Interphase Condition in Cavitation Analysis
J. Tribol (October,2016)
Related Proceedings Papers
Related Chapters
A Reduced Order Gas Pressure Law for Single Acoustic Cavitation Bubbles
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Test Methods
Consensus on Operating Practices for the Sampling and Monitoring of Feedwater and Boiler Water Chemistry in Modern Industrial Boilers (CRTD-81)
Hydrodynamic Lubrication
Design of Mechanical Bearings in Cardiac Assist Devices