Abstract
The topic of sustainable machining has in recent times emerged as a significant and impactful area of research focus as it directly deals with environmental health and protection, economic growth and prosperity, and societal wellbeing with greater health and wellness. More specifically, sustainable machining at product, process, and system levels deals with reducing negative environmental impact, offering improved energy and resource efficiency, generating a minimum quantity of wastes, providing operational safety, and offering improved personal health. This paper summarizes recent efforts by the world research community in sustainable machining with a systematic approach for the analysis of machining processes that are broadly classified as sustainable, beginning with dry machining, and then near-dry (also known as minimum quantity lubrication (MQL)) and cryogenic machining processes. The paper also extends its analysis to a hybrid mode of sustainable machining that effectively combines cryogenic and MQL machining processes for improved productivity and machining performance. While a significant part of this paper presents experimental analysis, the progress being made in modeling and optimization has also been discussed in the paper. In particular, major challenges involved in model development for practical implementation, with a view to selecting optimum cutting conditions and cutting tool selection, are primarily discussed in the paper. The need for continued modeling efforts for achieving deployable optimized conditions for sustainable machining is highly recognized, and further research is required in numerous fronts integrating the various convergent disciplines such as materials, mechanics, computational sciences, economics, environmental sciences.
References
1.
US Department of Commerce
, 2009
. How does Commerce Define Sustainable Manufacturing
.2.
US EPA
, 2012
. Sustainable Manufacturing
, https://www.epa.gov/sustainability/sustainable-manufacturing.3.
NACFAM
, 2009
. Sustainable Manufacturing
.4.
Rachuri
, S.
, Sriram
, R.
, Narayanan
, A.
, Sarkar
, P.
, Lee
, J.
, Lyons
, K.
, and Kemmerer
, S., 2010.
Sustainable Manufacturing: Metrics, Standards, and Infrastructure—NIST Workshop Report
, National Institute of Standards and Technology (NIST)
, Gaithersburg, MD
, NIST Interagency/Internal report (NISTIR), 7683
.5.
ASME
, 2011
. Sustainable Products and Processes Strategic Plan
.6.
ASME
, 2014
. Sustainable Manufacturing: Preparing for a New Business Imperative, Open Research Forum (ORF-2), Report and Recommendations
.7.
NSF
, 2014
, “Report on Sustainable Manufacturing Development Roadmap Workshop,” T. E. Y.
Huang
, M.
El-Halwagi
, C.
Davidson
, and M.
Eden
, Cincinnati, OH
.8.
Jayal
, A.
, Badurdeen
, F.
, Dillon
, O.
, Jr, and Jawahir
, I.
, 2010
, “Sustainable Manufacturing: Modeling and Optimization Challenges at the Product, Process and System Levels
,” CIRP J. Manuf. Sci. Technol.
, 2
(3
), pp. 144
–152
. 10.1016/j.cirpj.2010.03.0069.
Jawahir
, I. S.
, Badurdeen
, F.
, and Rouch
, K. E.
, 2013
, “Innovation in Sustainable Manufacturing Education
”, Proceeding of 11th Global Conference on Sustainable Manufacturing (GCSM)
G.
Seliger
, ed., Berlin, Germany
, Sept. 23–25
, pp. 9
–16
.10.
Institute for Sustainable Manufacturing (ISM)
, 2014
, Sustainable Manufacturing—A Business Perspective: A technology roadmap
.11.
Carley
, S.
, Jasinowski
, J.
, Glassley
, G.
, Strahan
, P.
, Attari
, S.
, and Shackelford
, S.
, 2014
, Success Paths to Sustainable Manufacturing
, School of Public and Environmental Affairs Indiana University
, Bloomington, IN
.12.
Wanigarathne
, P.
, Liew
, J.
, Wang
, X.
, Dillon
, O.
, Jr, and Jawahir
, I.
, 2004
, “Assessment of Process Sustainability for Product Manufacture in Machining Operations
,” Proceedings of the Global Conference on Sustainable Product Development and Life Cycle Engineering
, Berlin, Germany
, pp. 305
–312
.13.
Lu
, T.
, 2014
, “A Metrics-Based Sustainability Assessment of Cryogenic Machining Using Modeling and Optimization of Process Performance
,” PhD thesis, University of Kentucky
.14.
Lu
, T.
, and Jawahir
, I.
, 2015
, “Metrics-Based Sustainability Evaluation of Cryogenic Machining
,” Procedia CIRP
, 29
, pp. 520
–525
. 10.1016/j.procir.2015.02.06715.
Byers
, J. P.
, 2006
, Metalworking Fluids
, CRC Press, Taylor and Francis Group
, Boca Raton, FL
.16.
Hong
, S. Y.
, 2006
, “Lubrication Mechanisms of LN2 in Ecological Cryogenic Machining
,” Mach. Sci. Technol.
, 10
(1
), pp. 133
–155
. 10.1080/1091034050053432417.
El Baradie
, M.
, 1996
, “Cutting Fluids: Part I. Characterisation
,” J. Mater. Process. Technol.
, 56
(1-4
), pp. 786
–797
. 10.1016/0924-0136(95)01892-118.
Shokrani
, A.
, Dhokia
, V.
, and Newman
, S. T.
, 2012
, “Environmentally Conscious Machining of Difficult-to-Machine Materials With Regard to Cutting Fluids
,” Int. J. Mach. Tools Manuf.
, 57
, pp. 83
–101
. 10.1016/j.ijmachtools.2012.02.00219.
Shokrani
, A.
, Dhokia
, V.
, and Newman
, S.
, 2014
, “A Techno-Health Study of the Use of Cutting Fluids and Future Alternatives
,” 24th International Conference on Flexible Automation and Intelligent Manufacturing (FAIM 2014)
, San Antonio, TX
.20.
Clapp
, R. W.
, Jacobs
, M. M.
, and Loechler
, E. L.
, 2008
, “Environmental and Occupational Causes of Cancer: new Evidence 2005-2007
,” Reviews Environ. Health
, 23
(1
), pp. 1
–38
. 10.1515/REVEH.2008.23.1.121.
Malloy
, E. J.
, Miller
, K. L.
, and Eisen
, E. A.
, 2007
, “Rectal Cancer and Exposure to Metalworking Fluids in the Automobile Manufacturing Industry
,” Occup. Environ. Med.
, 64
(4
), pp. 244
–249
. 10.1136/oem.2006.02730022.
De Joode
, B. V. W.
, Bierman
, E.
, Brouwer
, D.
, Spithoven
, J.
, and Kromhout
, H.
, 2005
, “An Assessment of Dermal Exposure to Semi-Synthetic Metal Working Fluids by Different Methods to Group Workers for an Epidemiological Study on Dermatitis
,” Occup. Environ. Medicine
, 62
(9
), pp. 633
–641
. 10.1136/oem.2004.01539623.
Klocke
, F.
, and Eisenblätter
, G.
, 1997
, “Dry Cutting
,” CIRP Ann.
, 46
(2
), pp. 519
–526
. 10.1016/S0007-8506(07)60877-424.
Brinksmeier
, E.
, Meyer
, D.
, Huesmann-Cordes
, A.
, and Herrmann
, C.
, 2015
, “Metalworking Fluids—Mechanisms and Performance
,” CIRP Ann.
, 64
(2
), pp. 605
–628
. 10.1016/j.cirp.2015.05.00325.
Jawahir
, I. S.
, Attia
, H.
, Biermann
, D.
, Duflou
, J.
, Klocke
, F.
, Meyer
, D.
, Newman
, S.
, Pusavec
, F.
, Putz
, M.
, and Rech
, J.
, 2016
, “Cryogenic Manufacturing Processes
,” CIRP Ann.
, 65
(2
), pp. 713
–736
. 10.1016/j.cirp.2016.06.00726.
Taylor
, F. W.
, 1907
, On the Art of Cutting Metals
, 2nd ed., Vol. 28
, ASME
, New York
.27.
Cook
, N. H.
, 1973
, “Tool Wear and Tool Life
,” ASME J. Eng. Ind.
, 95
(4
), pp. 931
–938
. 10.1115/1.343827128.
ANSI/ASME
, 1985
, Tool-life Testing with Single-Point Turning Tools
, American National Standard
, New York
.29.
Colding
, B. N.
, 1959
, “A Three-Dimensional, Tool-Life Equation—Machining Economics
,” ASME J. Eng. Ind.
, 81
(3
), pp. 239
–249
. 10.1115/1.400831330.
Rubenstein
, C.
, 1976
, An Analysis of Tool Life Based on Flank-Face Wear—Part 2: Comparison of Theory With Experimental Observations
.31.
Usui
, E.
, Shirakashi
, T.
, and Kitagawa
, T.
, 1984
, “Analytical Prediction of Cutting Tool Wear
,” Wear
, 100
(1–3
), pp. 129
–151
. 10.1016/0043-1648(84)90010-332.
ISO
, 1993
, 3685, in: Tool-life Testing of Turning Tools
.33.
Chandrasekaran
, H.
, and Johansson
, J.
, 1994
, “Chip Flow and Notch Wear Mechanisms During the Machining of High Austenitic Stainless Steels
,” CIRP Ann.
, 43
(1
), pp. 101
–105
. 10.1016/S0007-8506(07)62174-X34.
Venkatesh
, V.
, and Satchithanandam
, M.
, 1980
, “A Discussion on Tool Life Criteria and Total Failure Causes
,” CIRP Ann.
, 29
(1
), pp. 19
–22
. 10.1016/S0007-8506(07)61288-835.
Reinhart
, L. E.
, 1975
, Effect of Chip Forming Devices on Tool Wear in Metal Cutting
.36.
Jawahir
, I. S.
, 1991
, “An Investigation of Three-Dimensional Chip Flow in Machining of Steels With Grooved Chip Forming Tool Inserts
,” Transactions NAMRI/SME
, 19
, pp. 222
–231
.37.
Worthington
, B.
, 1976
, “The Operation and Performance of a Groove-Type Chip Forming Device
,” Int. J. Production Res.
, 14
(5
), pp. 529
–558
. 10.1080/0020754760895662338.
Jawahir
, I.
, Li
, P.
, Gosh
, R.
, and Exner
, E.
, 1995
, “A New Parametric Approach for the Assessment of Comprehensive Tool Wear in Coated Grooved Tools
,” CIRP Ann.
, 44
(1
), pp. 49
–54
. 10.1016/S0007-8506(07)62273-239.
Li
, P.
, Jawahir
, I.
, Fang
, X.
, and Exner
, E.
, 1996
, “Chip-groove Effects on Multiple Tool-Wear Parameters in Machining
,” NAMRI SME
, Ann Arbor, MI
, May 21–23
, pp. 33
–38
.40.
Jawahir
, I. S.
, Fang
, X. D.
, Li
, P. X.
, and Ghosh
, R.
, 1997
, Method of Assessing Tool-Life in Grooved Tools
, US Patent 5,689,062
.41.
Jawahir
, I.
, Ghosh
, R.
, Fang
, X.
, and Li
, P.
, 1995
, “An Investigation of the Effects of Chip Flow on Tool-Wear in Machining With Complex Grooved Tools
,” Wear
, 184
(2
), pp. 145
–154
. 10.1016/0043-1648(94)06572-142.
Ee
, K.
, Balaji
, A.
, Li
, P.
, and Jawahir
, I.
, 2001
, “Force Decomposition Model for Tool-Wear in Turning With Grooved Cutting Tools
,” Wear
, 249
(10–11
), pp. 985
–994
. 10.1016/S0043-1648(01)00837-743.
Ghosh
, R.
, Redetzky
, M.
, Balaji
, A.
, and Jawahir
, I.
, 1996
, “The Equivalent Toolface (ET) Approach for Modeling Chip Curl in Machining With Grooved Tools
,” Proceeding of CSME Forum 13th Symposium on Engineering Applications of Mechanics: Manufacturing Science and Engineering
, McMaster University, Hamilton, Ontario, Canada
, pp. 702
–711
.44.
Ee
, K.
, Balaji
, A.
, and Jawahir
, I.
, 2003
, “Progressive Tool-Wear Mechanisms and Their Effects on Chip-Curl/Chip-Form in Machining With Grooved Tools: An Extended Application of the Equivalent Toolface (ET) Model
,” Wear
, 255
(7–12
), pp. 1404
–1413
. 10.1016/S0043-1648(03)00112-145.
Ee
, K.
, Li
, P.
, Balaji
, A.
, Jawahir
, I.
, and Stevenson
, R.
, 2006
, “Performance-based Predictive Models and Optimization Methods for Turning Operations and Applications: Part 1—Tool Wear/Tool Life in Turning with Coated Grooved Tools
,” J. Manuf. Processes
, 8
(1
), pp. 54
–66
. 10.1016/S1526-6125(06)70102-546.
Marksberry
, P.
, and Jawahir
, I.
, 2008
, “A Comprehensive Tool-Wear/Tool-Life Performance Model in the Evaluation of NDM (Near dry Machining) for Sustainable Manufacturing
,” Int. J. Mach. Tools Manuf.
, 48
(7–8
), pp. 878
–886
. 10.1016/j.ijmachtools.2007.11.00647.
Ernst
, H.
, and Merchant
, M. E.
, 1941
, Chip Formation, Friction and Finish
, Cincinnati Milling Machine Company
, Cincinnati, OH
.48.
Lee
, E.
, 1951
, “The Theory of Plasticity Applied to a Problem of Machining
,” ASME J. Appl. Mech.
, 18
(1
), p. 405
.49.
Palmer
, W.
, and Oxley
, P.
, 1959
, “Mechanics of Orthogonal Machining
,” Proceedings Ins. Mech. Eng.
, 173
(1
), pp. 623
–654
. 10.1243/PIME_PROC_1959_173_053_0250.
Johnson
, W.
, 1962
, “Some Slip-Line Fields for Swaging or Expanding, Indenting, Extruding and Machining for Tools With Curved Dies
,” Int. J. Mech. Sci.
, 4
(4
), pp. 323
–347
. 10.1016/S0020-7403(62)80022-851.
Oxley
, P. L. B.
, 1962
, “An Analysis for Orthogonal Cutting With Restricted Tool-Chip Contact
,” Int. J. Mech. Sci.
, 4
(2
), pp. 129
–135
. 10.1016/S0020-7403(62)80035-652.
Jawahir
, I. S.
, and Oxley
, P. L. B.
, 1988
, “The Tool Restricted Contact Effect as a Major Influencing Factor in Chip Breaking: An Experimental Analysis
,” CIRP Ann.
, 17
(1
), pp. 121
–126
. 10.1016/S0007-8506(07)61600-X53.
Fang
, N.
, Jawahir
, I. S.
, and Oxley
, P. L. B.
, 2001
, “A Universal Slip-Line Model With Non-Unique Solutions for Machining With Curled Chip Formation and a Restricted Contact Tool
,” Int. J. Mech. Sci.
, 43
(2
), pp. 557
–580
. 10.1016/S0020-7403(99)00117-454.
Oxley
, P. L. B.
, 1989
, The Mechanics of Machining: An Analytical Approach to Assessing Machinability
, Ellis Horwood Publishers
, New York
.55.
Fang
, N.
, and Jawahir
, I.
, 2002
, “An Analytical Predictive Model and Experimental Validation for Machining With Grooved Tools Incorporating the Effects of Strains, Strain-Rates, and Temperatures
,” CIRP Ann.
, 51
(1
), pp. 83
–86
. 10.1016/S0007-8506(07)61471-156.
Wang
, X.
, and Jawahir
, I.
, 2007
, “Recent Advances in Plasticity Applications in Metal Machining: Slip-Line Models for Machining With Rounded Cutting Edge Restricted Contact Grooved Tools
,” Int. J. Mach. Mach. Mater.
, 2
(3/4
), p. 347
. 10.1504/IJMMM.2007.01547157.
Schoop
, J.
, Adeniji
, D.
, and Brown
, I.
, 2019
, “Computationally Efficient, Multi-Domain Hybrid Modeling of Surface Integrity in Machining and Related Thermomechanical Finishing Processes
,” Procedia CIRP
, 82
(1
), pp. 356
–361
. 10.1016/j.procir.2019.03.22558.
Okushima
, K.
, and Hitomi
, K.
, 1964
, “A Study of Economical Machining: an Analysis of the Maximum-Profit Cutting Speed
,” Int. J. Production Res.
, 3
(1
), pp. 73
–78
. 10.1080/0020754640894304659.
Armarego
, E.
, and Russell
, J.
, 1966
, “Maximum Profit Rate as a Criterion for the Selection of Machining Conditions
,” Int. J. Mach. Tool Design Res.
, 6
(1
), pp. 15
–23
. 10.1016/0020-7357(66)90003-560.
Zdeblick
, W. J.
, De Vor
, R.
, and Kahles
, J. F.
, 1981
, “A Comprehensive Machining Cost Model and Optimization Technique
,” CIRP Ann.
, 30
(1
), pp. 405
–408
. 10.1016/S0007-8506(07)60966-461.
Balaji
, A.
, Ghosh
, R.
, Fang
, X.
, Stevenson
, R.
, and Jawahir
, I.
, 2006
, “Performance-based Predictive Models and Optimization Methods for Turning Operations and Applications: Part 2—Assessment of Chip Forms/Chip Breakability
,” J. Manuf. Processes
, 8
(2
), pp. 144
–158
. 10.1016/S1526-6125(06)80009-562.
Wang
, X.
, Da
, Z.
, Balaji
, A.
, and Jawahir
, I.
, 2007
, “Performance-based Predictive Models and Optimization Methods for Turning Operations and Applications: Part 3—Optimum Cutting Conditions and Selection of Cutting Tools
,” J. Manuf. Processes
, 9
(1
), pp. 61
–74
. 10.1016/S1526-6125(07)70108-163.
Jawahir
, I.
, Balaji
, A.
, Rouch
, K.
, and Baker
, J.
, 2003
, “Towards Integration of Hybrid Models for Optimized Machining Performance in Intelligent Manufacturing Systems
,” J. Mater. Process. Technol.
, 139
(1–3
), pp. 488
–498
. 10.1016/S0924-0136(03)00525-964.
Jawahir
, I.
, Qureshi
, N.
, and Arsecularatne
, J.
, 1992
, “On the Interrelationships of Some Machinability Parameters in Finish Turning with Cermet Chip Forming Tool Inserts
,” Int. J. Mach. Tools Manuf.
, 32
(5
), pp. 709
–723
. 10.1016/0890-6955(92)90025-C65.
Shaw
, M. C.
, 2005
, Metal Cutting Principles
, Oxford University Press
, New York
.66.
Da
, Z.
, and Jawahir
, I.
, 1998
, “Optimal Chip Control in Turning Operations
,” Proceedings of the International Seminar on Improving Machine Tool Performance
, San Sebastian, Spain
, July 6–8
, pp. 607
–618
.67.
Jawahir
, I.
, and Wang
, X.
, 2007
, “Development of Hybrid Predictive Models and Optimization Techniques for Machining Operations
,” J. Mater. Process. Technol.
, 185
(1–3
), pp. 46
–59
. 10.1016/j.jmatprotec.2006.03.13368.
Wang
, X.
, and Jawahir
, I.
, 2005
, “Optimization of Multi-Pass Turning Operations Using Genetic Algorithms for the Selection of Cutting Conditions and Cutting Tools with Tool-Wear Effect
,” Int. J. Production Res.
, 43
(17
), pp. 3543
–3559
. 10.1080/1362939050012446569.
Eskicioglu
, H.
, Nisli
, M.
, and Kilic
, S.
, 1985
, “An Application of Geometric Programming to Single-Pass Turning Operations
,” Proceedings of the Twenty-Fifth International Machine Tool Design and Research Conference
, Birmingham, UK
, Apr. 22–24
, pp. 149
–157
.70.
Armarego
, E.
, Kee
, P.
, and Smith
, A.
, 1986
, “Computer Aided Optimization of Machining Conditions in Single Pass Turning Operations
,” Third International Conference on Manufacturing Engineering 1986: Technology for Manufacturing Growth; preprints of Papers
, Newcastle, NSW, Australia
, Aug. 4–6
, p. 36
.71.
Arsecularatne
, J. A.
, Hinduja
, S.
, and Barrow
, G.
, 1992
, “Optimum Cutting Conditions for Turned Components, Proceedings of the Institution of Mechanical Engineers
,” Part B: J. Eng. Manuf.
, 206
(1
), pp. 15
–31
. 10.1243/PIME_PROC_1992_206_052_0272.
Meng
, Q.
, Arsecularatne
, J.
, and Mathew
, P.
, 2000
, “Calculation of Optimum Cutting Conditions for Turning Operations Using a Machining Theory
,” Int. J. Mach. Tools Manuf.
, 40
(12
), pp. 1709
–1733
. 10.1016/S0890-6955(00)00026-273.
El-Gizawy
, A. S.
, and El-Sayed
, J. J.
, 2002
, “A Multiple Objective Based Strategy for Process Design of Machining Operations
,” Int. J. Comput. Integr. Manuf.
, 15
(4
), pp. 353
–360
. 10.1080/0951192011005908974.
Wang
, J.
, Kuriyagawa
, T.
, Wei
, X.
, and Guo
, D.
, 2002
, “Optimization of Cutting Conditions for Single Pass Turning Operations Using a Deterministic Approach
,” Int. J. Mach. Tools Manuf.
, 42
(9
), pp. 1023
–1033
. 10.1016/S0890-6955(02)00037-875.
Armarego
, E.
, and Ostafiev
, D.
, 2003
, “Multi-Constraint Optimization and Cutting Conditions Selection in Process Planning Turning Operations with Modern Chip Breaker Tools, Proceedings of the Institution of Mechanical Engineers
,” Part B: J. Eng. Manuf.
, 217
(1
), pp. 57
–71
. 10.1243/09544050376250228876.
Da
, Z.
, Sadler
, J.
, and Jawahir
, I.
, 1997
, “Predicting Optimum Cutting Conditions for Turning Operations at Varying Tool-Wear States
,” Transactions NAMRI SME
, Lincoln, NE
, May 21–23
, pp. 75
–80
.77.
Da
, Z.
, Sadler
, J.
, and Jawahir
, I.
, 1998
, A New Performance-Based Criterion for Optimum Cutting Conditions and Cuffing Tool Selection in Finish Turning
, SME Technical Paper
.78.
Sadler
, J. P.
, Jawahir
, I. S.
, Da
, Z.
, and Lee
, S. S.
, 1998
, Method of Predicting Optimum Machining Conditions
, US Patent 5,801,963
.79.
Sadler
, J. P.
, Jawahir
, I. S.
, Da
, Z.
, and Lee
, S. S.
, 1999
, Optimization of Machining with Progressively Worn Cutting Tools
, US Patent 5,903,474
.80.
Ermer
, D.
, and Kromodihardjo
, S.
, 1981
, Optimization of Multipass Turning With Constraints
.81.
Agapiou
, J.
, 1992
, The Optimization of Machining Operations Based on a Combined Criterion, Part 1: The Use of Combined Objectives in Single-Pass Operations
.82.
Mesquita
, R.
, Krasteva
, E.
, and Doytchinov
, S.
, 1995
, “Computer-Aided Selection of Optimum Machining Parameters in Multipass Turning
,” Int. J. Adv. Manuf. Technol.
, 10
(1
), pp. 19
–26
. 10.1007/BF0118427483.
Alberti
, N.
, and Perrone
, G.
, 1999
, “Multipass Machining Optimization by Using Fuzzy Possibilistic Programming and Genetic Algorithms, Proceedings of the Institution of Mechanical Engineers
,” Part B: J. Eng. Manuf.
, 213
(3
), pp. 261
–273
. 10.1243/095440599151674184.
Al-Ahmari
, A.
, 2001
, “Mathematical Model for Determining Machining Parameters in Multipass Turning Operations With Constraints
,” Int. J. Prod. Res.
, 39
(15
), pp. 3367
–3376
. 10.1080/0020754011005256285.
Onwubolu
, G.
, and Kumalo
, T.
, 2001
, “Optimization of Multipass Turning Operations With Genetic Algorithms
,” Int. J. Prod. Res.
, 39
(16
), pp. 3727
–3745
. 10.1080/0020754011005615386.
Vijayakumar
, K.
, Prabhaharan
, G.
, Asokan
, P.
, and Saravanan
, R.
, 2003
, “Optimization of Multi-Pass Turning Operations Using Ant Colony System
,” Int. J. Mach. Tools Manuf.
, 43
(15
), pp. 1633
–1639
. 10.1016/S0890-6955(03)00081-687.
Chen
, M.-C.
, 2004
, “Optimizing Machining Economics Models of Turning Operations Using the Scatter Search Approach
,” Int. J. Prod. Res.
, 42
(13
), pp. 2611
–2625
. 10.1080/0020754041000166625188.
Wang
, X.
, Da
, Z.
, Balaji
, A.
, and Jawahir
, I.
, 2002
, “Performance-Based Optimal Selection of Cutting Conditions and Cutting Tools in Multipass Turning Operations Using Genetic Algorithms
,” Int. J. Prod. Res.
, 40
(9
), pp. 2053
–2065
. 10.1080/0020754021012827989.
Klein
, E.
, 1974
, “Tool Wear and Cooling Action: The Influence of Mist Spraying in the Machining of Aluminum
,” Maschienenmarkt
, 80
, pp. 87
–91
.90.
Klein
, E.
, 1974
, “The Field of Application of Mist Spraying of Cutting Fluids With Practical Examples
,” Maschienenmarkt
, 80
, pp. 105
–110
.91.
Um
, J.-Y.
, Chow
, L. C.
, and Jawahir
, I. S.
, 1995
, “Experimental Investigation of the Application of the Spray Cooling Method in Stainless Steel Machining
,” ASME MED Manufacturing Science and Engineering
, 2
(1
), pp. 165
–178
.92.
Brinksmeier
, E.
, Walter
, A.
, Jansscn
, R.
, and Diersen
, P.
, 1999
, “Aspects of Cooling Lubrication Reduction in Machining Advanced Materials, Proceedings of the Institution of Mechanical Engineers
,” Part B: J. Eng. Manuf.
, 213
(8
), pp. 769
–778
. 10.1243/095440599151720993.
Weinert
, K.
, Inasaki
, I.
, Sutherland
, J. W.
, and Wakabayashi
, T.
, 2004
, “Dry Machining and Minimum Quantity Lubrication
,” CIRP Annals—Manuf. Technol.
, 53
(2
), pp. 511
–537
. 10.1016/S0007-8506(07)60027-494.
Suda
, S.
, Wakabayashi
, T.
, Inasaki
, I.
, and Yokota
, H.
, 2004
, “Multifunctional Application of a Synthetic Ester to Machine Tool Lubrication Based on MQL Machining Lubricants
,” CIRP Annals—Manuf. Technol.
, 53
(1
), pp. 61
–64
. 10.1016/S0007-8506(07)60645-395.
Lopes
, J. C.
, Garcia
, M. V.
, Valentim
, M.
, Javaroni
, R. L.
, Ribeiro
, F. S. F.
, de Angelo Sanchez
, L. E.
, de Mello
, H. J.
, Aguiar
, P. R.
, and Bianchi
, E. C.
, 2019
, “Grinding Performance Using Variants of the MQL Technique: MQL With Cooled Air and MQL Simultaneous to the Wheel Cleaning jet
,” Int. J. Adv. Manuf. Technol.
, 105
(10
), pp. 4429
–4442
. 10.1007/s00170-019-04574-596.
Kamata
, Y.
, Obikawa
, T.
, and Shinozuka
, J.
, 2004
, Analysis of Mist Flow in MQL Cutting
, Department of Mechanical Engineering, Tokyo Institute of Technology
, Meguro, Tokyo, Japan
, pp. 339
–344
.97.
Ohtake
, H.
, Tanaki
, T.
, and Koizumi
, Y.
Study on Boiling Heat Transfer and Critical Heat Flux in Mist Cooling (Effect of Droplet Size on Heat Transfer Characteristics)
, Department of Mechanical Engineering, Kogakuin University
, Japan
, pp. 691
–698
.98.
Kim
, S. H.
, Lee
, S. W.
, Han
, S.
, and Kim
, S. M.
, 2019
, “Numerical Investigation of Thermal Characteristics of Spray Cooling With Minimum Quantity Lubrication in Milling Process
,” Appl. Math. Model.
, 65
(1
), pp. 137
–147
. 10.1016/j.apm.2018.08.01199.
Redetzky
, M.
, Balaji
, A.
, and Jawahir
, I.
, 1999
, “Predictive Modeling of Cutting Forces and Chip Flow in Machining with Nose Radius Tools
,” Proceedings 2nd CIRP International Workshop on Modeling of Machining Operations
, Nantes, France
, July 3–5
, pp. 160
–180
.100.
Wanigarathne
, P. C.
, Ee
, K. C.
, and Jawahir
, I. S.
, 2003
, “Near-dry Machining for Environmentally Benign Manufacturing—A Comparison of Machining Performance with Flood Cooling and Dry Machining
,” Design Manuf. Sustainable Dev.
, 2003
(1
), pp. 39
–48
.101.
Puvanesan
, M.
, Rahman
, M. M.
, Najiha
, M. S.
, and Kadirgama
, K.
, 2014
, “Experimental Investigation of Minimum Quantity Lubrication on Tool Wear in Aluminum Alloy 6061-T6 Using Different Cutting Tools
,” Int. J. Automotive Mech. Eng.
, 9
(1
), pp. 1511
–1524
. 10.15282/ijame.9.2013.5.0127102.
Rahman
, M.
, Senthil Kumar
, A.
, and Manzoor Ul
, S.
, 2001
, “Evaluation of Minimal Quantities of Lubricant in End Milling
,” Int. J. Adv. Manuf. Technol.
, 18
(4
), pp. 235
–241
. 10.1007/s001700170063103.
Rahman
, M.
, Senthil Kumar
, A.
, and Salam
, M. U.
, 2002
, “Experimental Evaluation on the Effect of Minimal Quantities of Lubricant in Milling
,” Int. J. Mach. Tools Manuf.
, 42
(5
), pp. 539
–547
. 10.1016/S0890-6955(01)00160-2104.
Dhar
, N. R.
, Ahmed
, M. T.
, and Islam
, S.
, 2007
, “An Experimental Investigation on Effect of Minimum Quantity Lubrication in Machining AISI 1040 Steel
,” Int. J. Mach. Tools Manuf.
, 47
(5
), pp. 748
–753
. 10.1016/j.ijmachtools.2006.09.+999017105.
Dhar
, N. R.
, Kamruzzaman
, M.
, and Ahmed
, M.
, 2006
, “Effect of Minimum Quantity Lubrication (MQL) on Tool Wear and Surface Roughness in Turning AISI-4340 Steel
,” J. Mater. Process. Technol.
, 172
(2
), pp. 299
–304
. 10.1016/j.jmatprotec.2005.09.022106.
Itoigawa
, F.
, Childs
, T. H. C.
, Nakamura
, T.
, and Belluco
, W.
, 2006
, “Effects and Mechanisms in Minimal Quantity Lubrication Machining of an Aluminum Alloy
,” Wear
, 260
(3
), pp. 339
–344
. 10.1016/j.wear.2005.03.035107.
Attanasio
, A.
, Gelfi
, M.
, Giardini
, C.
, and Remino
, C.
, 2006
, “Minimal Quantity Lubrication in Turning: Effect on Tool Wear
,” Wear
, 260
(3
), pp. 333
–338
. 10.1016/j.wear.2005.04.024108.
Behera
, B. C.
, Alemayehu
, H.
, Ghosh
, S.
, and Rao
, P. V.
, 2017
, “A Comparative Study of Recent Lubri-Coolant Strategies for Turning of Ni-Based Superalloy
,” J. Manuf. Processes
, 30
(1
), pp. 541
–552
. 10.1016/j.jmapro.2017.10.027109.
Zhang
, S.
, Li
, J. F.
, and Wang
, Y. W.
, 2012
, “Tool Life and Cutting Forces in end Milling Inconel 718 Under dry and Minimum Quantity Cooling Lubrication Cutting Conditions
,” J. Cleaner Prod.
, 32
(1
), pp. 81
–87
. 10.1016/j.jclepro.2012.03.014110.
Pusavec
, F.
, Hamdi
, H.
, Kopac
, J.
, and Jawahir
, I.
, 2011
, “Surface Integrity in Cryogenic Machining of Nickel Based Alloy—Inconel 718
,” J. Mater. Process. Technol.
, 211
(4
), pp. 773
–783
. 10.1016/j.jmatprotec.2010.12.013111.
Pusavec
, F.
, Deshpande
, A.
, Yang
, S.
, M'Saoubi
, R.
, Kopac
, J.
, Dillon
, O. W.
, Jr, and Jawahir
, I.
, 2015
, “Sustainable Machining of High Temperature Nickel Alloy–Inconel 718: Part 2–Chip Breakability and Optimization
,” J. Cleaner Prod.
, 87
(1
), pp. 941
–952
. 10.1016/j.jclepro.2014.10.085112.
Li
, K. M.
, and Liang
, S. Y.
, 2007
, “Performance Profiling of Minimum Quantity Lubrication in Machining
,” Int. J. Adv. Manuf. Technol.
, 35
(3-4
), pp. 226
–233
. 10.1007/s00170-006-0713-1113.
Ji
, X.
, Li
, B.
, Zhang
, X.
, and Liang
, S. Y.
, 2014
, “The Effects of Minimum Quantity Lubrication (MQL) on Machining Force, Temperature, and Residual Stress
,” Int. J. Precis. Eng. Manuf.
, 15
(11
), pp. 2443
–2451
. 10.1007/s12541-014-0612-6114.
Ji
, X.
, Li
, B. Z.
, and Liang
, S. Y.
, 2018
, “Analysis of Thermal and Mechanical Effects on Residual Stress in Minimum Quantity Lubrication (MQL) Machining
,” J. Mech.
, 34
(1
), pp. 41
–46
. 10.1017/jmech.2016.14115.
Priarone
, P. C.
, Robiglio
, M.
, Settineri
, L.
, and Tebaldo
, V.
, 2016
, “Modelling of Specific Energy Requirements in Machining as a Function of Tool and Lubricoolant Usage
,” CIRP Annals—Manuf. Technol.
, 65
(1
), pp. 25
–28
. 10.1016/j.cirp.2016.04.108116.
Mia
, M.
, Bashir
, M. A.
, Khan
, M. A.
, and Dhar
, N. R.
, 2017
, “Optimization of MQL Flow Rate for Minimum Cutting Force and Surface Roughness in end Milling of Hardened Steel (HRC 40)
,” Int. J. Adv. Manuf. Technol.
, 89
(1–4
), pp. 675
–690
. 10.1007/s00170-016-9080-8117.
Uysal
, A.
, and Jawahir
, I. S.
, 2019
, “Validation of the Slip-Line Model for Serrated Chip Formation in Orthogonal Turning Under dry and MQL Conditions
,” Procedia CIRP
, 82
(1
), pp. 124
–129
. 10.1016/j.procir.2019.04.006118.
Tai
, B. L.
, Jessop
, A. J.
, Stephenson
, D. A.
, and Shih
, A. J.
, 2012
, “Workpiece Thermal Distortion in Minimum Quantity Lubrication Deep Hole Drilling-Finite Element Modeling and Experimental Validation
,” ASME J. Manuf. Sci. Eng.
, 134
(1
), p. 011008
. 10.1115/1.4005432119.
Tai
, B. L.
, Stephenson
, D. A.
, and Shih
, A. J.
, 2013
, “Workpiece Temperature During Deep-Hole Drilling of Cast Iron Using High air Pressure Minimum Quantity Lubrication
,” ASME J. Manuf. Sci. Eng.
, 135
(3
), p. 031019
. 10.1115/1.4024036120.
Biermann
, D.
, and Iovkov
, I.
, 2012
, “Deep Hole Drilling Using Twist Drills and MQL
,” WT Werkstattstechnik
, 102
(1
), pp. 324
–328
. 10.1016/j.procir.2012.07.043121.
Biermann
, D.
, and Iovkov
, I.
, 2015
, “Investigations on the Formation of Straightness Deviation in MQL Deep-Hole Drilling of Thin-Walled Aluminium Components: Experimental and Simulation-Based Analysis of Thermomechanical Effects in Deep-Hole Drilling Using Single-lip Drills and Twist Drills
,” Prod. Eng. Res. Devel.
, 9
(4
), pp. 527
–535
. 10.1007/s11740-015-0632-9122.
Scurlock
, R.
, 1990
, “A Matter of Degrees: A Brief History of Cryogenics
,” Cryogenics
, 30
(6
), pp. 483
–500
. 10.1016/0011-2275(90)90048-H123.
Gunston
, B.
, and Gunston
, B.
, 2009
, The Cambridge Aerospace Dictionary
, Cambridge University Press
, Cambridge, UK
.124.
Kaynak
, Y.
, and Gharibi
, A.
, 2018
, “Progressive Tool Wear in Cryogenic Machining: The Effect of Liquid Nitrogen and Carbon Dioxide
,” J. Manuf. Mater. Processing
, 2
(2
), p. 31
. 10.3390/jmmp2020031125.
Tahmasebi
, E.
, Albertelli
, P.
, Lucchini
, T.
, Monno
, M.
, and Mussi
, V.
, 2019
, “CFD and Experimental Analysis of the Coolant Flow in Cryogenic Milling
,” Int. J. Mach. Tools Manuf.
, 140
(1
), pp. 20
–33
. 10.1016/j.ijmachtools.2019.02.003126.
Pu
, Z.
, Outeiro
, J.
, Batista
, A.
, Dillon
, O.
, Jr, Puleo
, D.
, and Jawahir
, I. S.
, 2012
, “Enhanced Surface Integrity of AZ31B Mg Alloy by Cryogenic Machining Towards Improved Functional Performance of Machined Components
,” Int. J. Mach. Tools Manuf.
, 56
(1
), pp. 17
–27
. 10.1016/j.ijmachtools.2011.12.006127.
Lu
, T.
, Kudaravalli
, R.
, and Georgiou
, G.
, 2018
, “Cryogenic Machining Through the Spindle and Tool for Improved Machining Process Performance and Sustainability: Pt. I, System Design
,” Procedia Manuf.
, 21
(1
), pp. 266
–272
. 10.1016/j.promfg.2018.02.120128.
Hong
, S. Y.
, and Zhao
, Z.
, 1999
, “Thermal Aspects, Material Considerations and Cooling Strategies in Cryogenic Machining
,” Clean Prod. Processes
, 1
(2
), pp. 107
–116
. 10.1007/s100980050016129.
Kaynak
, Y.
, 2014
, “Evaluation of Machining Performance in Cryogenic Machining of Inconel 718 and Comparison with dry and MQL Machining
,” Int. J. Adv. Manuf. Technol.
, 72
(5–8
), pp. 919
–933
. 10.1007/s00170-014-5683-0130.
Schoop
, J.
, Sales
, W. F.
, and Jawahir
, I.
, 2017
, “High Speed Cryogenic Finish Machining of Ti-6Al4V with Polycrystalline Diamond Tools
,” J. Mater. Process. Technol.
, 250
(1
), pp. 1
–8
. 10.1016/j.jmatprotec.2017.07.002131.
Shokrani
, A.
, Dhokia
, V.
, Munoz-Escalona
, P.
, and Newman
, S.
, 2013
, “State-of-the-art Cryogenic Machining and Processing
,” Int. J. Comput. Integr. Manuf.
, 26
(7
), pp. 1
–33
. 10.1080/0951192x.2012.749531132.
Sales
, W. F.
, Schoop
, J.
, and Jawahir
, I.
, 2017
, “Tribological Behavior of PCD Tools During Superfinishing Turning of the Ti6Al4V Alloy Using Cryogenic, Hybrid and Flood as Lubri-Coolant Environments
,” Tribol. Int.
, 114
(1
), pp. 109
–120
. 10.1016/j.triboint.2017.03.038133.
Kaynak
, Y.
, and Gharibi
, A.
, 2019
, “Cryogenic Machining of Titanium Ti-5553 Alloy
,” ASME J. Manuf. Sci. Eng.
, 141
(4
), p. 041012
. 10.1115/1.4042605134.
Kaynak
, Y.
, Karaca
, H. E.
, Noebe
, R. D.
, and Jawahir
, I. S.
, 2013
, “Tool-wear Analysis in Cryogenic Machining of NiTi Shape Memory Alloys: A Comparison of Tool-Wear Performance With dry and MQL Machining
,” Wear
, 306
(1–2
), pp. 51
–63
. 10.1016/j.wear.2013.05.011135.
Ghosh
, R.
, Zurecki
, Z.
, and Frey
, J. H.
, 2003
, “Cryogenic Machining With Brittle Tools and Effects on Tool Life
,” Proceedings of ASME IMECE
, Washington, DC
, Nov. 15–21
.136.
Kaynak
, Y.
, Lu
, T.
, and Jawahir
, I. S.
, 2014
, “Cryogenic Machining-Induced Surface Integrity: A Review and Comparison With Dry,MQL, and Flood-Cooled Machining
,” Mach. Sci. Technol.: An Int. J.
, 18
(2
), pp. 149
–198
. 10.1080/10910344.2014.897836137.
Umbrello
, D.
, Micari
, F.
, and Jawahir
, I.
, 2012
, “The Effects of Cryogenic Cooling on Surface Integrity in Hard Machining: A Comparison With Dry Machining
,” CIRP Ann.
, 61
(1
), pp. 103
–106
. 10.1016/j.cirp.2012.03.052138.
Toth
, L. S.
, and Gu
, C.
, 2014
, “Ultrafine-Grain Metals by Severe Plastic Deformation
,” Mater. Charact.
, 92
(1
), pp. 1
–14
. 10.1016/j.matchar.2014.02.003139.
Doherty
, R.
, Hughes
, D.
, Humphreys
, F.
, Jonas
, J.
, Jensen
, D. J.
, Kassner
, M.
, King
, W.
, McNelley
, T.
, McQueen
, H.
, and Rollett
, A.
, 1997
, “Current Issues in Recrystallization: A Review
,” Mater. Sci. Eng. A
, 238
(2
), pp. 219
–274
. 10.1016/S0921-5093(97)00424-3140.
Ulutan
, D.
, and Ozel
, T.
, 2011
, “Machining Induced Surface Integrity in Titanium and Nickel Alloys: A Review
,” Int. J. Mach. Tool Manu.
, 51
(3
), pp. 250
–280
. 10.1016/j.ijmachtools.2010.11.003141.
Jawahir
, I.
, Kaynak
, Y.
, and Lu
, T.
, 2014
, “The Impact of Novel Material Processing Methods on Component Quality, Life and Performance
,” Procedia CIRP
, 22
(1
), pp. 33
–44
. 10.1016/j.procir.2014.09.001142.
Meyers
, M. A.
, and Chawla
, K. K.
, 2009
, Mechanical Behavior of Materials
, Cambridge University Press
, Cambridge, UK
.143.
O’Sullivan
, D.
, and Cotterell
, M.
, 2002
, “Machinability of Austenitic Stainless Steel SS303
,” J. Mater. Process. Technol.
, 124
(1–2
), pp. 153
–159
. 10.1016/S0924-0136(02)00197-8144.
Hong
, S. Y.
, and Broomer
, M.
, 2000
, “Economical and Ecological Cryogenic Machining of AISI 304 Austenitic Stainless Steel
,” Clean Prod. Processes.
, 2
(3
), pp. 157
–66
. 10.1007/s100980000073145.
Duerig
, T.
, Pelton
, A.
, and Stockel
, D.
, 1999
, An Overview of Nitinol Medical Applications
, Vol. 273–275
, Materials Science and Engineering: A
, pp. 149
–160
.146.
Thierry
, B.
, Tabrizian
, M.
, Trepanier
, C.
, Savadogo
, O.
, and Yahia
, L. H.
, 2000
, “Effect of Surface Treatment and Sterilization Processes on the Corrosion Behavior of NiTi Shape Memory Alloy
,” J. Biomed. Mater. Res.
, 51
(4
), pp. 685
–693
. 10.1002/1097-4636(20000915)51:4<685::AID-JBM17>3.0.CO;2-S147.
Yang
, S.
, 2012
, “Cryogenic Burnishing of Co-Cr-Mo Biomedical Alloy for Enhanced Surface Integrity and Improved Wear Performance
,” PhD dissertations, University of Kentucky
.148.
Yang
, S.
, Dillon
, O. W.
, Jr, Puleo
, D. A.
, and Jawahir
, I. S.
, 2013
, “Effect of Cryogenic Burnishing on Surface Integrity Modifications of Co-Cr-Mo Biomedical Alloy
,” J. Biomedical Mater. Res. Part B: Appl. Biomaterials
, 101
(1
), pp. 139
–152
. 10.1002/jbm.b.32827149.
Huang
, B.
, Kaynak
, Y.
, Arvin
, C.
, and Jawahir
, I.
, 2014
, “Improved Surface Integrity From Cryogenic Machining of Al 7050-T7451 Alloy with Ultra-Fine Grained Structure
,” 17th International Conference on Advances in Materials and Processing Technologies (AMPT 2014)
, Dubai, United Arab Emirates
, Nov. 13–15
.150.
Pu
, Z.
, Song
, G.-L.
, Yang
, S.
, Dillon
, O.
, Puleo
, D.
, and Jawahir
, I.
, 2011
, Cryogenic Burnishing of AZ31B Mg Alloy for Enhanced Corrosion Resistance
, Magnesium Technology 2011
, Cham, Switzerland, Springer
, pp. 513
–518
.151.
Rotella
, G.
, Dillon
, O.
, Umbrello
, D.
, Settineri
, L.
, and Jawahir
, I.
, 2014
, “The Effects of Cooling Conditions on Surface Integrity in Machining of Ti6Al4V Alloy
,” Int. J. Adv. Manuf. Technol.
, 71
(1–4
), pp. 47
–55
. 10.1007/s00170-013-5477-9152.
Arrazola
, P.
, Özel
, T.
, Umbrello
, D.
, Davies
, M.
, and Jawahir
, I.
, 2013
, “Recent Advances in Modelling of Metal Machining Processes
,” CIRP Ann.-Manuf. Technol.
, 62
(2
), pp. 695
–718
. 10.1016/j.cirp.2013.05.006153.
Caudill
, J.
, Schoop
, J.
, and Jawahir
, I.
, 2019
, “Numerical Modeling of Cutting Forces and Temperature Distribution in High Speed Cryogenic and Flood-Cooled Milling of Ti-6Al-4V
,” Procedia CIRP
, 82
(1
), pp. 83
–88
. 10.1016/j.procir.2019.04.055154.
Pusavec
, F.
, Lu
, T.
, Courbon
, C.
, Rech
, J.
, Aljancic
, U.
, Kopac
, J.
, and Jawahir
, I.
, 2016
, “Analysis of the Influence of Nitrogen Phase and Surface Heat Transfer Coefficient on Cryogenic Machining Performance
,” J. Mater. Process. Technol.
, 233
(1
), pp. 19
–28
. 10.1016/j.jmatprotec.2016.02.003155.
Pu
, Z.
, Umbrello
, D.
, Puleo
, D.
, Dillon
, O.
, Jr, Lu
, T.
, and Jawahir
, I.
, 2013
, “Finite Element Modeling of Microstructural Changes in Dry and Cryogenic Machining of AZ31B Magnesium Alloy for Enhanced Corrosion Resistance
,” Proc. NAMRI/SME
, 16
(2
), pp. 335
–343
. 10.1016/j.jmapro.2014.02.002156.
Pu
, Z.
, Umbrello
, D.
, Dillon
, O.
, Jr, and Jawahir
, I.
, 2014
, “Finite Element Simulation of Residual Stresses in Cryogenic Machining of AZ31B Mg Alloy
,” Procedia CIRP
, 13
(1
), pp. 282
–287
. 10.1016/j.procir.2014.04.048157.
Jawahir
, I.
, Puleo
, D.
, and Schoop
, J.
, 2016
, “Cryogenic Machining of Biomedical Implant Materials for Improved Functional Performance, Life and Sustainability
,” Procedia CIRP
, 46
(1
), pp. 7
–14
. 10.1016/j.procir.2016.04.133158.
Hanenkamp
, N.
, Amon
, S.
, and Gross
, D.
, 2018
, “Hybrid Supply System for Conventional and CO2/MQL-Based Cryogenic Cooling
,” Procedia CIRP
, 77
(1
), pp. 219
–222
. 10.1016/j.procir.2018.08.293159.
Pereira
, O.
, Rodríguez
, A.
, Fernández-Abia
, A.
, Barreiro
, J.
, and de Lacalle
, L. L.
, 2015
, “The Use of Hybrid CO2+MQL in Machining Operations
,” Procedia Eng.
, 132
(1
), pp. 492
–499
. 10.1016/j.proeng.2015.12.524160.
Cordes
, S.
, Hübner
, F.
, and Schaarschmidt
, T.
, 2014
, “Next Generation High Performance Cutting by Use of Carbon Dioxide as Cryogenics
,” Procedia Cirp
, 14
(1
), pp. 401
–405
. 10.1016/j.procir.2014.03.091161.
Iturbe
, A.
, Hormaetxe
, E.
, Garay
, A.
, and Arrazola
, P.
, 2016
, “Surface Integrity Analysis When Machining Inconel 718 With Conventional and Cryogenic Cooling
,” Procedia CIRP
, 45
(1
), pp. 67
–70
. 10.1016/j.procir.2016.02.095162.
Damir
, A.
, Shi
, B.
, and Attia
, M. H.
, 2019
, “Flow Characteristics of Optimized Hybrid Cryogenic-Minimum Quantity Lubrication Cooling in Machining of Aerospace Materials
,” CIRP Annals.
, 68
(1
), pp. 77
–80
. 10.1016/j.cirp.2019.04.047163.
Stephenson
, D.
, Skerlos
, S. J.
, King
, A. S.
, and Supekar
, S. D.
, 2014
, “Rough Turning Inconel 750 With Supercritical CO2-Based Minimum Quantity Lubrication
,” J. Mater. Process. Technol.
, 214
(3
), pp. 673
–680
. 10.1016/j.jmatprotec.2013.10.003164.
MacLean
, D. J.
, Hayes
, K. F.
, Barnard
, T.
, Hull
, T.
, Park
, Y. E.
, and Skerlos
, S. J.
, 2009
, “Impact of Supercritical Carbon Dioxide Metalworking Fluids on Tool Life in Turning of Sintered Steel and Milling of Compacted Graphite Iron
,” ASME IMCE
, Lake Buena Vista, FL
, Nov. 13–19
, American Society of Mechanical Engineers Digital Collection, pp. 43
–48
.165.
Pereira
, O.
, Rodríguez
, A.
, Barreiro
, J.
, Fernández-Abia
, A. I.
, and de Lacalle
, L. N. L.
, 2017
, “Nozzle Design for Combined use of MQL and Cryogenic gas in Machining
,” Int. J. Precision Eng. Manuf.-Green Technol.
, 4
(1
), pp. 87
–95
. 10.1007/s40684-017-0012-3166.
Pereira
, O.
, Urbikain
, G.
, Rodríguez
, A.
, Fernández-Valdivielso
, A.
, Calleja
, A.
, Ayesta
, I.
, and de Lacalle
, L. N. L.
, 2017
, “Internal Cryolubrication Approach for Inconel 718 Milling
,” Procedia Manuf.
, 13
(1
), pp. 89
–93
. 10.1016/j.promfg.2017.09.013167.
Tascioglu
, E.
, Gharibi
, A.
, and Kaynak
, Y.
, 2019
, “High Speed Machining of Near-Beta Titanium Ti-5553 Alloy Under Various Cooling and Lubrication Conditions
,” Int. J. Adv. Manuf. Technol.
, 102
(9–12
), pp. 4257
–4271
. 10.1007/s00170-019-03291-3168.
Kaynak
, Y.
, Karaca
, H. E.
, Noebe
, R. D.
, and Jawahir
, I.
, 2015
, “The Effect of Active Phase of the Work Material on Machining Performance of a NiTi Shape Memory Alloy
,” Metallurgical Mater. Transactions A
, 46
(6
), pp. 2625
–2636
. 10.1007/s11661-015-2828-1169.
Klocke
, F.
, Lung
, D.
, Arft
, M.
, Priarone
, P. C.
, and Settineri
, L.
, 2013
, “On High-Speed Turning of a Third-Generation Gamma Titanium Aluminide
,” Int. J. Adv. Manuf. Technol.
, 65
(1–4
), pp. 155
–163
. 10.1007/s00170-012-4157-5170.
Sun
, Y.
, Huang
, B.
, Puleo
, D. A.
, and Jawahir
, I. S.
, 2015
, “Enhanced Machinability of Ti-5553 Alloy From Cryogenic Machining: Comparison with MQL and Flood-Cooled Machining and Modeling
,” Procedia CIRP
, 31
(1
), pp. 477
–482
. 10.1016/j.procir.2015.03.099171.
Behrendt
, T.
, Zein
, A.
, and Min
, S.
, 2012
, “Development of an Energy Consumption Monitoring Procedure for Machine Tools
,” CIRP Ann.
, 61
(1
), pp. 43
–46
. 10.1016/j.cirp.2012.03.103172.
Lu
, T.
, and Jawahir
, I.
, 2018
, Energy Efficient Manuf.: Theory Appl.
, John Wiley & Sons
, Hoboken, NJ
, pp. 123
–157
.173.
Schoop
, J.
, Ambrosy
, F.
, Zanger
, F.
, Schulze
, V.
, Jawahir
, I. S.
, and Balk
, T. J.
, 2015
, “Increased Surface Integrity in Porous Tungsten From Cryogenic Machining with Cermet Cutting Tool
,” Mater. Manuf. Processes
, pp. 1
–9
. 10.1080/10426914.2015.1048467174.
Busbaher
, D.
, Schoop
, J.
, Jawahir
, I. S.
, and Balk
, T. J.
, 2015
, “Observations on Cutting Edge Radius Effects in Cryogenic Machining of Porous Tungsten
,” Vacuum Electronics Conference (IVEC), 2015
, Monterey, CA
, Apr. 27–29
, IEEE International, pp. 1
–2
.175.
Schoop
, J.
, Ambrosy
, F.
, Zanger
, F.
, Schulze
, V.
, Balk
, T. J.
, and Jawahir
, I. S.
, 2016
, “Cryogenic Machining of Porous Tungsten for Enhanced Surface Integrity
,” J. Mater. Process. Technol.
, 229
, pp. 614
–621
. 10.1016/j.jmatprotec.2015.10.002176.
Schoop
, J.
, Jawahir
, I. S.
, and Balk
, T. J.
, 2015
, “Size Effects in Finish Machining of Porous Powdered Metal for Engineered Surface Quality
,” Precision Eng.
, 44
(1
), pp. 180
–191
. 10.1016/j.precisioneng.2015.12.004177.
Lu
, T.
, Dillon
, O. W.
, and Jawahir
, I.
, 2013
, A Thermal Analysis Framework for Cryogenic Machining and its Contribution to Product and Process Sustainability
. 10.14279/depositonce-3753178.
Lauwers
, B.
, Klocke
, F.
, Klink
, A.
, Tekkaya
, A. E.
, Neugebauer
, R.
, and Mcintosh
, D.
, 2014
, “Hybrid Processes in Manufacturing
,” CIRP Ann.
, 63
(2
), pp. 561
–583
. 10.1016/j.cirp.2014.05.003179.
Williams
, S. W.
, Martina
, F.
, Addison
, A. C.
, Ding
, J.
, Pardal
, G.
, and Colegrove
, C.
, 2016
, “Wire + Arc Additive Manufacturing
,” Mater. Sci. Technol.
, 32
(7
), pp. 641
–647
. 10.1179/1743284715Y.0000000073Copyright © 2020 by ASME
You do not currently have access to this content.
