Accurate information about the evolution of the temperature field is a theoretical prerequisite for investigating grinding burn and optimizing the process parameters of grinding process. This paper proposed a new statistical model of equivalent grinding heat source with consideration of the random distribution of grains. Based on the definition of the Riemann integral, the summation limit of the discrete point heat sources was transformed into the integral of a continuous function. A finite element method (FEM) simulation was conducted to predict the grinding temperature field with the embedded net heat flux equation. The grinding temperature was measured with a specially designed in situ infrared system and was formulated by time–space processing. The reliability and correctness of the statistical heat source model were validated by both experimental temperature–time curves and the maximum grinding temperature, with a relative error of less than . Finally, through the FEM-based inversed calculation, an empirical equation was proposed to describe the heat transfer coefficient (HTC) changes in the grinding contact zone for both conventional grinding and creep feed grinding.
Issue Section:
Research Papers
References
1.
Lefebvre
, A.
, Vieville
, P.
, Lipinski
, P.
, and Lescalier
, C.
, 2006
, “Numerical Analysis of Grinding Temperature Measurement by the Foil/Workpiece Thermocouple Method
,” Int. J. Mach. Tools Manuf.
, 46
(14
), pp. 1716
–1726
.2.
Jaeger
, J. C.
, 1942
, “Moving Sources of Heat and the Temperature of Sliding Contacts
,” J. Proc. R. Soc. New South Wales
, 76, pp. 203–224.3.
Mamalis
, A.
, Manolakos
, D.
, Markopoulos
, A.
, Kunádrk
, J.
, and Gyáni
, K.
, 2003
, “Thermal Modelling of Surface Grinding Using Implicit Finite Element Techniques
,” Int. J. Adv. Manuf. Technol.
, 21
(12
), pp. 929
–934
.4.
Lefebvre
, A.
, Lanzetta
, F.
, Lipinski
, P.
, and Torrance
, A.
, 2012
, “Measurement of Grinding Temperatures Using a Foil/Workpiece Thermocouple
,” Int. J. Mach. Tools Manuf.
, 58
, pp. 1
–10
.5.
Rowe
, W.
, Black
, S.
, Mills
, B.
, Qi
, H.
, and Morgan
, M.
, 1995
, “Experimental Investigation of Heat Transfer in Grinding
,” CIRP Ann. Manuf. Technol.
, 44
(1
), pp. 329
–332
.6.
Liao
, Y.
, Luo
, S.
, and Yang
, T.
, 2000
, “A Thermal Model of the Wet Grinding Process
,” J. Mater. Process. Technol.
, 101
(1
), pp. 137
–145
.7.
Jiang
, J.
, Ge
, P.
, Sun
, S.
, Wang
, D.
, Wang
, Y.
, and Yang
, Y.
, 2016
, “From the Microscopic Interaction Mechanism to the Grinding Temperature Field: An Integrated Modelling on the Grinding Process
,” Int. J. Mach. Tools Manuf.
, 110
, pp. 27
–42
.8.
Dyakonov
, A. A.
, 2014
, “Simulated Stochastic Thermo-Physical Model of Grinding Process,” World Congress on Engineering and Computer Science (WCECS
), San Francisco, CA, Oct. 22–24, pp. 914–917http://www.iaeng.org/publication/WCECS2014/WCECS2014_pp871-875.pdf.9.
Rumford
, B. C. O.
, 1798
, “An Inquiry Concerning the Source of the Heat Which Is Excited by Friction. By Benjamin Count of Rumford, FRSMRIA
,” Philos. Trans. R. Soc. London Ser. I
, 88
, pp. 80
–102
.10.
Shore
, H.
, 1924
, Tool and Chip Temperatures in Machine Shop Practice
, Massachusetts Institute of Technology
, Cambridge, MA
.11.
Schwerd
, F.
, 1933
, “Determination of the Temperature Distribution During Cutting Z
,” VDI Z.
, 77
, pp. 211
–216
.12.
Boothroyd
, G.
, 1961
, “Photographic Technique for the Determination of Metal Cutting Temperatures
,” Br. J. Appl. Phys.
, 12
(5
), p. 238
.13.
Ueda
, T.
, Hosokawa
, A.
, and Yamamoto
, A.
, 1986
, “Measurement of Grinding Temperature Using Infrared Radiation Pyrometer With Optical Fiber
,” ASME J. Eng. Ind.
, 108
(4
), pp. 247
–251
.14.
Kato
, T.
, and Fujii
, H.
, 1997
, “Temperature Measurement of Workpiece in Surface Grinding by PVD Film Method
,” ASME J. Manuf. Sci. Eng.
, 119
(4B
), pp. 689
–694
.15.
Yoshioka
, H.
, Hashizume
, H.
, and Shinn
, H.
, 2004
, “In-Process Microsensor for Ultraprecision Machining
,” IEEE Proc. Sci., Meas. Technol.
, 151
(2
), pp. 121
–125
.16.
Ueda
, T.
, Hosokawa
, A.
, and Yamamoto
, A.
, 1985
, “Studies on Temperature of Abrasive Grains in Grinding—Application of Infrared Radiation Pyrometer
,” ASME J. Manuf. Sci. Eng.
, 107
(2
), pp. 127
–133
. 17.
Upadhyaya
, R.
, and Malkin
, S.
, 2004
, “Thermal Aspects of Grinding With Electroplated CBN Wheels
,” ASME J. Manuf. Sci. Eng.
, 126
(1
), pp. 107
–114
.18.
Li
, Z.
, Ding
, W.
, Shen
, L.
, Xi
, X.
, and Fu
, Y.
, 2016
, “Comparative Investigation on High-Speed Grinding of TiCp/Ti–6Al–4V Particulate Reinforced Titanium Matrix Composites With Single-Layer Electroplated and Brazed CBN Wheels
,” Chin. J. Aeronaut.
, 29
(5
), pp. 1414
–1424
.19.
Chandrasekar
, S.
, Farris
, T.
, and Bhushan
, B.
, 1990
, “Grinding Temperatures for Magnetic Ceramics and Steel
,” ASME J. Tribol.
, 112
(3
), pp. 535
–541
.20.
Kops
, L.
, and Shaw
, M. C.
, 1982
, “Thermal Radiation in Surface Grinding
,” CIRP Ann. Manuf. Technol.
, 31
(1
), pp. 211
–214
.21.
Xu
, X.
, 2001
, “Experimental Study on Temperatures and Energy Partition at the Diamond–Granite Interface in Grinding
,” Tribol. Int.
, 34
(6
), pp. 419
–426
.22.
Hwang
, J.
, Kompella
, S.
, Chandrasekar
, S.
, and Farris
, T. N.
, 2003
, “Measurement of Temperature Field in Surface Grinding Using Infra-Red (IR) Imaging System
,” ASME J. Tribol.
, 125
(2
), pp. 377
–383
.23.
Jin
, T.
, Stephenson
, D.
, and Rowe
, W.
, 2003
, “Estimation of the Convection Heat Transfer Coefficient of Coolant Within the Grinding Zone
,” Proc. Inst. Mech. Eng., Part B
, 217
(3
), pp. 397
–407
.24.
Malkin
, S. G. C.
, 2008
, Grinding Technology: Theory and Applications of Machining With Abrasives
, Industrial Press
, South Norwalk, CT
.25.
Ohbuchi
, Y.
, and Matsuo
, T.
, 1991
, “Force and Chip Formation in Single-Grit Orthogonal Cutting With Shaped CBN and Diamond Grains
,” CIRP Ann. Manuf. Technol.
, 40
(1
), pp. 327
–330
.26.
Outwater
, J.
, and Shaw
, M.
, 1952
, “Surface Temperatures in Grinding
,” Trans. ASME
, 74
(1
), p. 73
. https://ci.nii.ac.jp/naid/10010081046/27.
Hahn
, R. S.
, 1962
, “On the Nature of the Grinding Process
,” Third Machine Tool Design and Research Conference
, Birmingham, UK, Sept. 24–28, pp. 129
–154.
28.
Lavine
, A.
, Malkin
, S.
, and Jen
, T.
, 1989
, “Thermal Aspects of Grinding With CBN Wheels
,” CIRP Ann. Manuf. Technol.
, 38
(1
), pp. 557
–560
.29.
Yan
, L.
, Rong
, Y.
, and Jiang
, F.
, 2011
, “Quantitative Evaluation and Modeling of Alumina Grinding Wheel Surface Topography
,” Jixie Gongcheng Xuebao(Chin. J. Mech. Eng.)
, 47
(17
), pp. 179
–186
.30.
Parente
, M. P. L.
, Jorge
, R. M. N.
, Vieira
, A. A.
, and Baptista
, A. M.
, 2012
, “Experimental and Numerical Study of the Temperature Field During Creep Feed Grinding
,” Int. J. Adv. Manuf. Technol.
, 61
(1–4
), pp. 127
–134
.31.
Nie
, Z.
, Wang
, G.
, Lin
, Y.
, and Rong
, Y.
, 2015
, “Precision Measurement and Modeling of Quenching-Tempering Distortion in Low-Alloy Steel Components With Internal Threads
,” J. Mater. Eng. Perform.
, 24
(12
), pp. 1
–12
.32.
Bergman
, T. L.
, 2011
, Introduction to Heat Transfer
, Wiley
, Hoboken, NJ
.33.
Bergman
, T. L.
, and Incropera
, F. P.
, 2011
, Fundamentals of Heat and Mass Transfer
, Wiley
, Hoboken, NJ
.34.
Khabari
, A.
, Zenouzi
, M.
, O'Connor
, T.
, and Rodas
, A.
, 2014
, “Natural and Forced Convective Heat Transfer Analysis of Nanostructured Surface
,” World Congress on Engineering (WCE
), London, July 2–4. http://www.iaeng.org/publication/WCE2014/WCE2014_pp317-319.pdf35.
Lavine
, A. S.
, 1988
, “A Simple Model for Convective Cooling During the Grinding Process
,” ASME J. Eng. Ind.
, 110
(1
), pp. 1
–6
.36.
Nie
, Z.
, Wang
, G.
, Yu
, J.
, Liu
, D.
, and Rong
, Y.
, 2016
, “Phase-Based Constitutive Modeling and Experimental Study for Dynamic Mechanical Behavior of Martensitic Stainless Steel Under High Strain Rate in a Thermal Cycle
,” Mech. Mater.
, 101
, pp. 160
–169
.37.
Liu
, D.
, Wang
, G.
, Nie
, Z.
, and Rong
, Y.
, 2016
, “An In-Situ Infrared Temperature-Measurement Method With Back Focusing on Surface for Creep-Feed Grinding
,” Measurement
, 94
, pp. 645
–652
.38.
Ichida
, Y.
, 2001
, “Creep Feed Profile Grinding of Ni-Based Superalloys With Ultrafine-Polycrystalline cBN Abrasive Grits
,” Precision Eng.
, 25
(4
), pp. 274
–283
.39.
Grigoriev
, S. N.
, Starkov
, V. K.
, Gorin
, N. A.
, Krajnik
, P.
, and Kopac
, J.
, 2014
, “Creep-Feed Grinding: An Overview of Kinematics, Parameters and Effects on Process Efficiency
,” Strojniški Vestnik-J. Mech. Eng.
, 60
(4
), pp. 213
–220
.40.
Kim
, H.-J.
, Kim
, N.-K.
, and Kwak
, J.-S.
, 2006
, “Heat Flux Distribution Model by Sequential Algorithm of Inverse Heat Transfer for Determining Workpiece Temperature in Creep Feed Grinding
,” Int. J. Mach. Tools Manuf.
, 46
(15
), pp. 2086
–2093
.41.
Du
, P.
, Wang
, G.
, Nie
, Z.
, and Rong
, Y.
, 2014
, “A FEM‐Based Inverse Calculation Method for Determination of Heat Transfer Coefficient in Liquid Quenching Process
,” TMS 143rd Annual Meeting & Exhibition
, San Diego, CA, Feb. 16–20, p. 309
. 42.
Lin
, B.
, Morgan
, M. N.
, Chen
, X. W.
, and Wang
, Y. K.
, 2009
, “Study on the Convection Heat Transfer Coefficient of Coolant and the Maximum Temperature in the Grinding Process
,” Int. J. Adv. Manuf. Technol.
, 42
(11
), pp. 1175
–1186
.Copyright © 2018 by ASME
You do not currently have access to this content.
