High-performance turbomachinery demands high shaft speeds, increased rotor flexibility, tighter clearances in the flow passages, advanced materials, and increased tolerance to imbalances. Operation at high speeds induces severe dynamic loading with large amplitude shaft motions at the bearing supports. Typical rotordynamic models rely on linearized force coefficients (stiffness K, damping C, and inertia M) to model the reaction forces from fluid film bearings and seal elements. These true linear force coefficients are derived from infinitesimally small amplitude motions about an equilibrium position. Often, however, a rotor–bearing system does not reach an equilibrium position and displaces with motions amounting to a sizable portion of the film clearance; the most notable example being a squeeze film damper (SFD). Clearly, linearized force coefficients cannot be used in situations exceeding its basic formulation. Conversely, the current speed of computing permits to evaluate fluid film element reaction forces in real time for ready numerical integration of the transient response of complex rotor–bearing systems. This approach albeit fast does not help to gauge the importance of individual effects on system response. Presently, an orbit analysis method estimates force coefficients from numerical simulations of specified journal motions and predicted fluid film reaction forces. For identical operating conditions in static eccentricity and whirl amplitude and frequency as those in measurements, the computational physics model calculates instantaneous damper reaction forces during one full period of motion and performs a Fourier analysis to characterize the fundamental components of the dynamic forces. The procedure is repeated over a range of frequencies to accumulate sets of forces and displacements building mechanical transfer functions from which force coefficients are identified. These coefficients thus represent best fits to the motion over a frequency range and dissipate the same mechanical energy as the nonlinear mechanical element. More accurate than the true linearized coefficients, force coefficients from the orbit analysis correlate best with SFD test data, in particular for large amplitude motions, statically off-centered. The comparisons also reveal the fallacy in representing nonlinear systems as simple K–C–M models impervious to the kinematics of motion.
Skip Nav Destination
Article navigation
February 2016
Research-Article
Orbit-Model Force Coefficients for Fluid Film Bearings: A Step Beyond Linearization
Luis San Andrés,
Luis San Andrés
Mast-Childs Chair Professor
Fellow ASME
Mechanical Engineering Department,
Texas A&M University,
College Station, TX 77843
e-mail: Lsanandres@tamu.edu
Fellow ASME
Mechanical Engineering Department,
Texas A&M University,
College Station, TX 77843
e-mail: Lsanandres@tamu.edu
Search for other works by this author on:
Sung-Hwa Jeung
Sung-Hwa Jeung
Mechanical Engineering Department,
Texas A&M University,
College Station, TX 77843
e-mail: sean.jeung@gmail.com
Texas A&M University,
College Station, TX 77843
e-mail: sean.jeung@gmail.com
Search for other works by this author on:
Luis San Andrés
Mast-Childs Chair Professor
Fellow ASME
Mechanical Engineering Department,
Texas A&M University,
College Station, TX 77843
e-mail: Lsanandres@tamu.edu
Fellow ASME
Mechanical Engineering Department,
Texas A&M University,
College Station, TX 77843
e-mail: Lsanandres@tamu.edu
Sung-Hwa Jeung
Mechanical Engineering Department,
Texas A&M University,
College Station, TX 77843
e-mail: sean.jeung@gmail.com
Texas A&M University,
College Station, TX 77843
e-mail: sean.jeung@gmail.com
1Corresponding author.
Contributed by the Structures and Dynamics Committee of ASME for publication in the JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Manuscript received June 23, 2015; final manuscript received July 21, 2015; published online September 1, 2015. Editor: David Wisler.
J. Eng. Gas Turbines Power. Feb 2016, 138(2): 022502 (11 pages)
Published Online: September 1, 2015
Article history
Received:
June 23, 2015
Revision Received:
July 21, 2015
Citation
San Andrés, L., and Jeung, S. (September 1, 2015). "Orbit-Model Force Coefficients for Fluid Film Bearings: A Step Beyond Linearization." ASME. J. Eng. Gas Turbines Power. February 2016; 138(2): 022502. https://doi.org/10.1115/1.4031237
Download citation file:
Get Email Alerts
A Multi-Stage Nonlinear Method for Aeroengine Health Parameter Estimation Based on Adjacent Operating Points
J. Eng. Gas Turbines Power
A Combined Experimental and Turbulence-Resolved Modeling Approach for Aeroengine Turbine Rim Seals
J. Eng. Gas Turbines Power (August 2024)
Related Articles
Theoretical and Experimental Comparisons for Damping Coefficients of a Short-Length Open-End Squeeze Film Damper
J. Eng. Gas Turbines Power (October,1996)
Eccentric Operation of the Squeeze-Film Damper
J. of Lubrication Tech (July,1978)
Air Entrainment Versus Lubricant Vaporization in Squeeze Film Dampers: An Experimental Assessment of Their Fundamental Differences
J. Eng. Gas Turbines Power (October,2001)
Experimental Performance of an Open Ends, Centrally Grooved, Squeeze Film Damper Operating With Large Amplitude Orbital Motions
J. Eng. Gas Turbines Power (March,2015)
Related Proceedings Papers
Related Chapters
Average Shaft Centerline Plots
Fundamentals of Rotating Machinery Diagnostics
Summary and Conclusions
Bearing Dynamic Coefficients in Rotordynamics: Computation Methods and Practical Applications
Fundamentals of Structural Dynamics
Flow Induced Vibration of Power and Process Plant Components: A Practical Workbook