Abstract
In this work, the application of a phenomenological model to determine engine-out hydrocarbon (HC) emissions in driving cycles is presented. The calculation is coupled to a physical-based simulation environment consisting of interacting submodels of engine, vehicle, and engine control. As a novelty, this virtual calibration methodology can be applied to optimize the energy conversion inside a spark-ignited (SI) internal combustion engine at transient operation. Using detailed information about the combustion process, the main origins and formation mechanisms of unburned HCs like piston crevice, oil layer, and wall quenching are considered in the prediction, as well as the in-cylinder postoxidation. Several parameterization approaches, especially, of the oil layer mechanism are discussed. After calibrating the emission model to a steady-state engine map, the transient results are validated successfully against measurements of various driving cycles based on different calibration strategies of engine operation.
Issue Section:
Fuel Combustion
Topics:
Cycles,
Cylinders,
Emissions,
Engines,
Fuels,
Combustion,
Simulation,
Quenching (Metalworking),
Pistons,
Steady state
References
1.
Weiss
,
M.
,
Bonnel
,
P.
,
Hummel
,
R.
, and
Steininger
,
N.
, 2013
,
“A Complementary Emissions Test for Light-Duty Vehicles:
Assessing the Technical Feasibility of Candidate
Procedures
,” European Commission, JRC Scientific and Policy
Reports, Brussels, Belgium, Report No. EUR 25572 EN.2.
Blizard
,
N. C.
, and
Keck
, J.
C.
, 1974
,
“Experimental and Theoretical Investigation of Turbulent
Burning Model for Internal Combustion Engines
,”
SAE
Paper No. 740191.3.
Tabaczynski
,
R.
,
Ferguson
,
C.
, and
Radhakrishnan
,
K.
, 1977
,
“A Turbulent Entrainment Model for Spark-Ignition Engine
Combustion
,” SAE
Paper No. 770647.4.
Santavicca
,
D.
,
Liou
,
D.
, and
North
,
G.
, 1990
,
“A Fractal Model of Turbulent Flame Kernel
Growth
,” SAE
Paper No. 900024.5.
D'Errico
,
G.
, and
Onorati
,
A.
, 2006
,
“Thermo-Fluid Dynamic Modelling of a Six-Cylinder Spark
Ignition Engine With a Secondary Air Injection System
,”
Int. J. Engine Res.
, 7
(1
),
pp. 1
–16
.6.
Dorsch
,
M.
,
Neumann
,
J.
, and
Hasse
,
C.
, 2014
,
“Detailed Modeling of SI Engines in Driving Cycle Simulations
for Fuel Consumption Analysis
,” FISITA World Automotive
Congress, Maastricht, The Netherlands, June 2–6, Paper No.
F2014-CET-017.7.
Dorsch
,
M.
,
Neumann
,
J.
, and
Hasse
,
C.
, 2014
,
“Nutzung der Ladungswechsel- und Motorprozesssimulation zur
Gesamtsystembewertung von CO2- und Rohemissionen in
Fahrzyklen
,” 7. MTZ-Fachtagung Ladungswechsel im
Verbrennungsmotor.8.
Cheng
,
W. K.
,
Hamrin
,
D.
,
Heywood
, J.
B.
,
Hochgreb
,
S.
,
Min
,
K.
, and
Norris
,
M.
, 1993
,
“An Overview of Hydrocarbon Emissions Mechanisms in
Spark-Ignition Engines
,” SAE
Paper No.
932708.9.
Min
,
K.
, 1994
,
“The Effects of Crevices on the Engine-Out Hydrocarbon
Emissions in Spark Ignition Engines
,” Ph.D. thesis,
Massachusetts Institute of Technology, Cambridge, MA.10.
Hochgreb
,
S.
, 1998
,
“Combustion-Related Emissions in SI Engines
,”
Handbook of Air Pollution From Internal Combustion Engines:
Pollutant Formation and Control
,
Academic
, San Diego,
CA
.11.
Borrmeister
,
J.
, and
Hübner
,
W.
, 1997
,
“Einfluss der Brennraumform auf HC-Emission und den
Verbrennungsablauf
,” Motortech. Z.
,
58
(7/8
), pp.
2
–8
.12.
Janssen
,
C.
, 2010
,
“Möglichkeiten zur Prädiktion von unverbrannten
Kohlenwasserstoffen in einem direkteinspritzenden
Ottomotor
,” Ph.D. thesis, Universität Rostock, Rostock,
Germany.13.
Merker
,
G. P.
,
Schwarz
,
C.
,
Stiesch
,
G.
, and
Otto
,
F.
, 2006
,
Verbrennungsmotoren-Simulation der Verbrennung und
Schadstoffbildung
, Vieweg+Teubner
Verlag
, Wiesbaden,
Germany
.14.
Huang
,
Z.
,
Pan
,
K.
,
Li
,
J.
,
Zhou
,
L.
, and
Jiang
,
D.
, 1996
,
“An Investigation on Simulation Models and Reduction Methods
of Unburned Hydrocarbon Emissions in Spark Ignition
Engines
,” Combust. Sci. Technol.
,
115
(1–3
), pp.
105
–123
.15.
Suck
,
G.
, 2001
,
“Untersuchung der HC-Quellen an einem Ottomotor mit
Direkteinspritzung
,” Ph.D. thesis,
Otto-von-Guericke-Universität Magdeburg, Magdeburg, Germany.16.
Spicher
,
U.
,
Feng
,
B.
, and
Kölmel
,
A.
, 1999
,
“HC Rohemissionen beim Kaltstart in der Warmlaufphase sowie
bei Last-und Drehzahlsprungen
,” Forschungsbericht
FZKA-BWPLUS, Institut für Kolbenmaschinen Universität Karlsruhe, Germany, Report
No. PEF396003.17.
Dent
,
J. C.
, and
Lakshminarayanan
, P.
A.
, 1983
, “A
Model for Adsorption and Desorption of Fuel Vapour by Cylinder Lubricating
Oil Films and Its Contribution to Hydrocarbon Emissions
,”
SAE
Paper No. 830652.18.
Frølund
,
K.
, and
Schramm
,
J.
, 1997
,
“Simulation of HC-Emissions From SI-Engines—A Parametric
Study
,” SAE
Paper No. 972893.19.
Gatellier
,
B.
,
Trapy
,
J.
,
Herrier
,
D.
,
Quelin
, J.
M.
, and Galliot
,
F.
, 1992
,
“Hydrocarbon Emissions of SI Engines as Influenced by Fuel
Absorption-Desorption in Oil Films
,” SAE
Paper No. 920095.20.
Sodre
,
J. R.
, 1998
,
“A Parametric Model for Spark Ignition Engine Turbulent Flame
Speed
,” SAE
Paper No. 982920.21.
Hasse
,
C.
,
Bollig
,
M.
,
Peters
,
N.
, and
Dwyer
, H.
A.
, 2000
, “Quenching
of Laminar Iso-Octane Flames at Cold Walls
,”
Combust. Flame
, 122
(1–2
),
pp. 117
–129
.22.
Schramm
,
J.
, and
Sorenson
, S.
C.
, 1990
, “A
Model for Hydrocarbon Emissions From SI Engines
,”
SAE
Paper No. 902169.23.
Trinker
,
F. H.
,
Chen
,
J.
, and
Davis
, G.
C.
, 1993
, “A Feedgas
HC Emission Model for SI Engines Including Partial Burn
Effects
,” SAE
Paper No. 932705.24.
Norris
,
M. G.
, and
Hochgreb
,
S.
, 1996
,
“Extent of Oxidation From the Lubricant Oil Layer in
Spark-Ignition Engines
,” SAE
Paper No.
960069.25.
Nefischer
,
A.
,
Neumann
,
J.
,
Stanciu
,
A.
, and
Wimmer
,
A.
, 2014
,
“Quasi-Dimensional Modeling of Turbulence-Driven Phenomena in
SI Engines
,” Int. J. Veh. Des.
,
66
(3
), pp.
297
–316
.26.
Grasreiner
,
S.
,
Neumann
,
J.
,
Luttermann
,
C.
,
Wensing
,
M.
, and
Hasse
,
C.
, 2014
,
“A Quasi-Dimensional Model of Turbulence and Global Charge
Motion for SI Engines With Fully-Variable Valve-Trains
,”
Int. J. Engine Res.
, 15
(7
),
pp. 805
–816
.27.
Grasreiner
,
S.
,
Neumann
,
J.
,
Wensing
,
M.
, and
Hasse
,
C.
, 2015
,
“A Quasi-Dimensional Model of the Ignition Delay for
Combustion Modeling in SI Engines
,” ASME J. Eng. Gas
Turbines Power
, 137
(7
), p.
071502
.28.
Wentworth
,
J. T.
, 1974
,
“Effect of Combustion Chamber Shape and Spark Location on
Exhaust Nitric Oxide and Hydrocarbon Emissions
,”
SAE
Paper No. 740529.29.
Yildrim
,
A. M.
,
Gul
, M.
Z.
, Ozatay
,
E.
, and
Karamangil
,
I.
, 2006
,
“Simulation of Hydrocarbon Emissions From an SI
Engine
,” SAE
Paper No. 2006-01-1196.30.
Linna
,
J. R.
, 1997
,
“Contribution of Oil Layer Mechanism to the Hydrocarbon
Emissions From Spark-Ignition Engines
,” Ph.D. thesis,
Massachusetts Institute of Technology
,
Cambridge, MA
.31.
Sodre
,
J. R.
, and
Yates
, D.
A.
, 1997
, “An
Improved Model for Spark Ignition Engine Exhaust
Hydrocarbon
,” SAE
Paper No. 971011.32.
Wilke
,
C. R.
, and
Chang
,
P.
, 1955
,
“Correlation of Diffusion Coefficients in Dilute
Solutions
,” AIChE J.
,
1
(2
), pp.
264
–270
.33.
Norris
,
M. G.
, and
Hochgreb
,
S.
, 1994
,
“Novel Experiment on In-Cylinder Desorption of Fuel From Oil
Layer
,” SAE
Paper No. 941963.34.
Watkins
,
R. C.
, 1984
,
“The Physics of Lubricant Additives
,”
Phys. Technol.
, 15
(6
), pp.
321
–328
.35.
Linna
,
J.-R.
,
Malberg
,
H.
,
Bennett
, P.
J.
, Palmer
,
J.
,
Tian
,
T.
, and
Cheng
, W.
K.
, 1997
,
“Contribution of Oil Layer Mechanism to the Hydrocarbon
Emissions From Spark-Ignition Engines
,” SAE
Paper No. 972892.36.
Kreith
,
F.
, 1960
,
Principles of Heat Transfer
, International
Textbook Company
, Scranton,
PA
.37.
Woschni
,
G.
, 1967
,
“A Universally Applicable Equation for the Instantaneous Heat
Transfer Coefficient in the Internal Combustion Engine
,”
SAE
Paper No. 670931.38.
Grill
,
M.
,
Billinger
,
T.
, and
Bargende
,
M.
, 2006
,
“Quasi-Dimensional Modeling of Spark Ignition Engine
Combustion With Variable Valve Train
,” SAE
Paper No. 2006-01-1107.39.
Peters
,
N.
, 2000
,
Turbulent Combustion
(Cambridge Monographs on Mechanics),
Cambridge University
,
Cambridge, UK
.40.
Metghalchi
,
M.
, and
Keck
, J.
C.
, 1982
, “Burning
Velocities of Mixtures of Air and Methanol, Isooctane and Indolene an High
Pressure and Temperature
,” Combust. Flame
,
48
, pp. 191
–210
.41.
Curran
,
H. J.
,
Gaffuri
,
P.
,
Pitz
, W.
J.
, and
Westbrook
, C.
K.
, 2002
, “A
Comprehensive Modeling Study of Iso-Octane Oxidation
,”
Combust. Flame
, 129
(3
), pp.
253
–280
.42.
Joos
,
F.
, 2006
,
Technische Verbrennung, Verbrennungstechnik,
Verbrennungsmodellierung, Emissionen
, Springer
Verlag
,
Berlin
.43.
Wu
,
K.-C.
,
Hochgreb
,
S.
, and
Norris
, M.
G.
, 1995
, “Chemical
Kinetic Modeling of Exhaust Hydrocarbon Oxidation
,”
Combust. Flame
, 100
(1
), pp.
193
–201
.44.
Oliveira
,
I. B.
, and
Hochgreb
,
S.
, 1999
,
“Effect of Operating Conditions and Fuel Type on Crevice HC
Emissions: Model Results and Comparison With Experiments
,”
SAE
Paper No. 1999-01-3578.45.
Lavoie
,
G. A.
, 1978
,
“Correlations of Combustion Data for S.I. Engine
Calculations—Laminar Flame Speed, Quench Distance and Global Reaction
Rates
,” SAE
Paper No. 780229.46.
Sodre
,
J. R.
, 1999
,
“Further Improvements on a HC Emissions Model: Partial Burn
Effects
,” SAE
Paper No.
1999-01-0222.47.
Min
,
K.
, and
Cheng
, W.
K.
, 1995
, “Oxidation
of the Piston Crevice Hydrocarbon During the Expansion Process in a Spark
Ignition Engine
,” Combust. Sci. Technol.
,
106
(617
), pp.
307
–326
.Copyright © 2016 by ASME
You do not currently have access to this content.
