Both experimental and theoretical investigations on the heat transfer and flow friction characteristics of compact cold plates have been performed. From the results, the local and average temperature rises on the cold plate surface increase with increasing chip heat flux or decreasing air mass flow rate. Besides, the effect of chip heat flux on the thermal resistance of cold plate is insignificant; while the thermal resistance of cold plate decreases with increasing air mass flow rate. Three empirical correlations of thermal resistance in terms of air mass flow rate with a power of −0.228 are presented. As for average Nusselt number, the effect of chip heat flux on the average Nusselt number is insignificant; while the average Nusselt number of the cold plate increases with increasing Reynolds number. An empirical relationship between Nu¯cp and Re can be correlated. In the flow frictional aspect, the overall pressure drop of the cold plate increases with increasing air mass flow rate; while it is insignificantly affected by chip heat flux. An empirical correlation of the overall pressure drop in terms of air mass flow rate with a power of 1.265 is presented. Finally, both heat transfer performance factor “j” and pumping power factor “f” decrease with increasing Reynolds number in a power of 0.805; while they are independent of chip heat flux. The Colburn analogy can be adequately employed in the study.

Issue Section:
Technical Papers
Keywords:
integrated circuit packaging, cooling, thermal resistance, heat exchangers, forced convection, thermal management (packaging), temperature distribution, channel flow, Cold Plate, Thermal Resistance, Nusselt Number, Reynolds Number, Heat Transfer Performance Factor, Pumping Power Factor, Colburn Analogy
Topics:
Flow (Dynamics), Heat transfer, Plates (structures), Temperature, Thermal resistance, Heat flux, Pressure drop, Friction, Heat, Reynolds number, Thermal analysis
1.
Kraus, A. D., and Bar-Cohen, A., 1983, Thermal Analysis and Control of Electronic Equipment, Hemisphere Publishing Corporation, Washington, DC.
2.
Kays, W. M., and London, A. L., 1984, Compact Heat Exchangers, 3rd Edition, McGraw-Hill, New York, NY.
3.
LaHaye
,
P. G.
,
Neugebauer
,
F. J.
, and
Sakhuja
,
R. K.
,
1974
, “
A Generalized Prediction of Heat Transfer Surfaces
,”
ASME J. Heat Transfer
,
96
, pp.
511
–
517
.
4.
Hung, Y. H., and Chun, Y. H., 1994, “Thermal Performance Analysis of Cold Plates for Multi-Layer Structures with Arbitrary Heating Loads,” ASME HTD-Vol. 292, Heat Transfer in Electronic System, pp. 137–144.
5.
Hung, Y. H., and Chiou, Y. M., 1996, “Computer-Aided Design for Multi-Layer Cold Plates with Arbitrary Heating Loads,” Proc., Technical Conference, 1996 International Electronics Packaging Society Conference, Austin, TX, September 29-October 1, pp. 285–296.
6.
Wang, L. S., Liu, C. Y., and Hung, Y. H., 1998, “Thermal Computer-Aided Design for Multi-Layer Structures Integrated with Cold Plate,” Proc., Eleventh International Symposium on Transport Phenomena (ISTP-11), November 29-December 3, pp. 17–22.
7.
Hung, Y. H., and Chen Y. Y., and Liu, C. Y, 1999, “Thermal CAD Package for Multilayer Printed Circuit Boards Integrated with Two-Stack Cold Plate,” Advances in Electronic Packaging-1999, ASME EEP-Vol. 26-2, pp. 2177–2184.
8.
Sathe, S. B., Stutzman, R. J., and Kosteva, S. J., 1994, “Development of a High Performance Low Pressure Drop Water Cold-Plate for Electronic Packaging Applications,” ASME HTD- Vol. 292, Heat Transfer in Electronic System, pp. 123–128.
9.
Ellison, G. N., 1984, Thermal Computations for Electronic Equipment, van Nostrand Reinhold Co., New York, NY
10.
Kline, S. J., and McClintock, F. A., 1953, “Describing Uncertainties in Single-Sample Experiments,” Mech. Eng. (Am. Soc. Mech. Eng.), pp. 3–8.
11.
Moffat
,
R. J.
,
1988
, “
Describing the Uncertainties in Experimental Results
,”
Exp. Therm. Fluid Sci.
,
1
, pp.
3
–
17
.
12.
Piper, R. J., and Kraus, A. D., 1995, “Cold Plates with Asymmetric Heat Loading—Part I: The Single Stack,” ASME EEP-Vol. 10-2, Advances in Electronic Packaging, pp. 865–870.
13.
Wang, M. P., 2000, “Forced Convective Heat Transfer in A Rectangular Hollow or Porous Channel,” Master’s thesis, Dept. of Power Mechanical Engineering, National Tsing Hua University, Taiwan.
14.
Chapman, A. J., 1987, Fundamental of Heat Transfer, Macmillan Publishing Company, New York, NY, pp. 295–296, 302–304.
Copyright © 2003
 by ASME
You do not currently have access to this content.