Abstract
The structure of the cathode catalyst layer (CCL) is critically important for improving the performance, durability, and stability of polymer electrolyte fuel cells (PEFCs). In this study, we designed CCLs with a three-dimensional (3D) structure that could increase the surface area of the CCLs to decrease their oxygen transfer resistance. The CCLs were fabricated using an inkjet printing method, and the electrochemical performance of the CCLs in a membrane electrode assembly was evaluated using an actual cell. The results showed that at high Pt loadings, the performance of the CCL with the 3D structure was superior to that of the flat structure. In particular, at a high current density, which is related to mass transport resistance, the two structures exhibited a significant difference in performance. At a Pt loading of 0.3 mg/cm2, the CCL with the 3D structure showed the highest maximum power density among all the CCLs investigated in this study. This indicates that the 3D structure decreases the oxygen transfer resistance of the CCL. Overall, the 3D structure provided improved morphological and microstructural characteristics to the CCL for fuel cell applications.
References
1.
Inoue
, G.
, 2016
, “Secondary Batteries and Fuel Cell Systems for Next-Generation Vehicles,” Energy Technology Roadmaps of Japan
, Y.
Kato
, M.
Koyama
, Y.
Fukushima
, and T.
Nakagaki
, eds., Springer Japan
, Tokyo
, pp. 537
–547
.2.
Debe
, M. K.
, 2012
, “Electrocatalyst Approaches and Challenges for Automotive Fuel Cells
,” Nature
, 486
(7401
), pp. 43
–51
. 3.
Yoon
, W.
, and Weber
, A. Z.
, 2011
, “Modeling Low-Platinum-Loading Effects in Fuel-Cell Catalyst Layers
,” J. Electrochem. Soc.
, 158
(8
), p. B1007
. 4.
Wilson
, A.
, Kleen
, G.
, and Papageorgopoulos
, D.
, 2017
, “DOE Hydrogen and Fuel Cells Program Record,” Fuel Cell System Cost—2017
. 5.
Liu
, W.
, Suzuki
, T.
, Mao
, H.
, and Schmiedel
, T.
, 2013
, “Development of Thin, Reinforced PEMFC Membranes Through Understanding of Structure-Property-Performance Relationships
,” ECS Trans.
, 50
(2
), pp. 51
–64
. 6.
Darling
, R. M.
, 2018
, “A Hierarchical Model for Oxygen Transport in Agglomerates in the Cathode Catalyst Layer of a Polymer-Electrolyte Fuel Cell
,” J. Electrochem. Soc.
, 165
(9
), pp. F571
–F580
. 7.
So
, M.
, Park
, K.
, Tsuge
, Y.
, and Inoue
, G.
, 2020
, “A Particle Based Ionomer Attachment Model for a Fuel Cell Catalyst Layer
,” J. Electrochem. Soc.
, 167
(1
), p. 013544
. 8.
Inoue
, G.
, Yokoyama
, K.
, Ooyama
, J.
, Terao
, T.
, Tokunaga
, T.
, Kubo
, N.
, and Kawase
, M.
, 2016
, “Theoretical Examination of Effective Oxygen Diffusion Coefficient and Electrical Conductivity of Polymer Electrolyte Fuel Cell Porous Components
,” J. Power Sources
, 327
, pp. 610
–621
. 9.
Sambandam
, S.
, Parrondo
, J.
, and Ramani
, V.
, 2013
, “Estimation of Electrode Ionomer Oxygen Permeability and Ionomer-Phase Oxygen Transport Resistance in Polymer Electrolyte Fuel Cells
,” Phys. Chem. Chem. Phys.
, 15
(36
), pp. 14994
–15002
. 10.
Sun
, X.
, Yu
, H.
, Zhou
, L.
, Gao
, X.
, Zeng
, Y.
, Yao
, D.
, He
, L.
, and Shao
, Z.
, 2020
, “Influence of Platinum Dispersity on Oxygen Transport Resistance and Performance in PEMFC
,” Electrochim. Acta
, 332
, p. 135474
. 11.
Cetinbas
, F. C.
, Ahluwalia
, R. K.
, Kariuki
, N. N.
, De Andrade
, V.
, and Myers
, D. J.
, 2020
, “Effects of Porous Carbon Morphology, Agglomerate Structure and Relative Humidity on Local Oxygen Transport Resistance
,” J. Electrochem. Soc.
, 167
(1
), p. 013508
. 12.
Inoue
, G.
, Ohnishi
, T.
, So
, M.
, Park
, K.
, Ono
, M.
, and Tsuge
, Y.
, 2019
, “Simulation of Carbon Black Aggregate and Evaluation of Ionomer Structure on Carbon in Catalyst Layer of Polymer Electrolyte Fuel Cell
,” J. Power Sources
, 439
, p. 227060
. 13.
So
, M.
, Park
, K.
, Ohnishi
, T.
, Ono
, M.
, Tsuge
, Y.
, and Inoue
, G.
, 2019
, “A Discrete Particle Packing Model for the Formation of a Catalyst Layer in Polymer Electrolyte Fuel Cells
,” Int. J. Hydrogen Energy
, 44
(60
), pp. 32170
–32183
. 14.
O’Neil
, K.
, Meyers
, J. P.
, Darling
, R. M.
, and Perry
, M. L.
, 2012
, “Oxygen Gain Analysis for Proton Exchange Membrane Fuel Cells
,” Int. J. Hydrogen Energy
, 37
(1
), pp. 373
–382
. 15.
Fernández
, R.
, Ferreira-Aparicio
, P.
, and Daza
, L.
, 2005
, “PEMFC Electrode Preparation: Influence of the Solvent Composition and Evaporation Rate on the Catalytic Layer Microstructure
,” J. Power Sources
, 151
(1–2
), pp. 18
–24
. 16.
Ngo
, T. T.
, Yu
, T. L.
, and Lin
, H. L.
, 2013
, “Influence of the Composition of Isopropyl Alcohol/Water Mixture Solvents in Catalyst Ink Solutions on Proton Exchange Membrane Fuel Cell Performance
,” J. Power Sources
, 225
, pp. 293
–303
. 17.
So
, M.
, Ohnishi
, T.
, Park
, K.
, Ono
, M.
, Tsuge
, Y.
, and Inoue
, G.
, 2019
, “The Effect of Solvent and Ionomer on Agglomeration in Fuel Cell Catalyst Inks: Simulation by the Discrete Element Method
,” Int. J. Hydrogen Energy
, 44
(54
), pp. 28984
–28995
. 18.
Suzuki
, T.
, Tsushima
, S.
, and Hirai
, S.
, 2013
, “Fabrication and Performance Evaluation of Structurally-Controlled PEMFC Catalyst Layers by Blending Platinum-Supported and Stand-Alone Carbon Black
,” J. Power Sources
, 233
, pp. 269
–276
. 19.
Mao
, Q.
, Sun
, G.
, Wang
, S.
, Sun
, H.
, Wang
, G.
, Gao
, Y.
, Ye
, A.
, Tian
, Y.
, and Xin
, Q.
, 2007
, “Comparative Studies of Configurations and Preparation Methods for Direct Methanol Fuel Cell Electrodes
,” Electrochim. Acta
, 52
(24
), pp. 6763
–6770
. 20.
Kim
, K.-H.
, Lee
, K.-Y.
, Kim
, H.-J.
, Cho
, E.
, Lee
, S.-Y.
, Lim
, T.-H.
, Yoon
, S. P.
, Hwang
, I. C.
, and Jang
, J. H.
, 2010
, “The Effects of Nafion® Ionomer Content in PEMFC MEAs Prepared by a Catalyst-Coated Membrane (CCM) Spraying Method
,” Int. J. Hydrogen Energy
, 35
(5
), pp. 2119
–2126
. 21.
Chaparro
, A. M.
, Gallardo
, B.
, Folgado
, M. A.
, Martín
, A. J.
, and Daza
, L.
, 2009
, “PEMFC Electrode Preparation by Electrospray: Optimization of Catalyst Load and Ionomer Content
,” Catal. Today
, 143
(3–4
), pp. 237
–241
. 22.
Wang
, Z.
, and Nagao
, Y.
, 2014
, “Effects of Nafion Impregnation Using Inkjet Printing for Membrane Electrode Assemblies in Polymer Electrolyte Membrane Fuel Cells
,” Electrochim. Acta
, 129
, pp. 343
–347
. 23.
Shukla
, S.
, Domican
, K.
, Karan
, K.
, Bhattacharjee
, S.
, and Secanell
, M.
, 2015
, “Analysis of Low Platinum Loading Thin Polymer Electrolyte Fuel Cell Electrodes Prepared by Inkjet Printing
,” Electrochim. Acta
, 156
, pp. 289
–300
. 24.
Park
, K.
, Ohnishi
, T.
, Goto
, M.
, So
, M.
, Takenaka
, S.
, Tsuge
, Y.
, and Inoue
, G.
, 2019
, “Improvement of Cell Performance in Catalyst Layers With Silica-Coated Pt/Carbon Catalysts for Polymer Electrolyte Fuel Cells
,” Int. J. Hydrogen Energy
, 45
(3
), pp. 1867
–1877
. 25.
Yu
, W.
, Zhou
, H.
, Li
, B. Q.
, and Ding
, S.
, 2017
, “3D Printing of Carbon Nanotubes-Based Microsupercapacitors
,” ACS Appl. Mater. Interfaces
, 9
(5
), pp. 4597
–4604
. 26.
Sun
, K.
, Wei
, T. S.
, Ahn
, B. Y.
, Seo
, J. Y.
, Dillon
, S. J.
, and Lewis
, J. A.
, 2013
, “3D Printing of Interdigitated Li-Ion Microbattery Architectures
,” Adv. Mater.
, 25
(33
), pp. 4539
–4543
. 27.
Gao
, T.
, Zhou
, Z.
, Yu
, J.
, Zhao
, J.
, Wang
, G.
, Cao
, D.
, Ding
, B.
, and Li
, Y.
, 2019
, “3D Printing of Tunable Energy Storage Devices With Both High Areal and Volumetric Energy Densities
,” Adv. Energy Mater.
, 9
(8
), pp. 1
–10
. 28.
Zhu
, C.
, Liu
, T.
, Qian
, F.
, Han
, T. Y. J.
, Duoss
, E. B.
, Kuntz
, J. D.
, Spadaccini
, C. M.
, Worsley
, M. A.
, and Li
, Y.
, 2016
, “Supercapacitors Based on Three-Dimensional Hierarchical Graphene Aerogels With Periodic Macropores
,” Nano Lett.
, 16
(6
), pp. 3448
–3456
. 29.
Liu
, C.
, Xu
, F.
, Cheng
, X.
, Tong
, J.
, Liu
, Y.
, Chen
, Z.
, Lao
, C.
, and Ma
, J.
, 2019
, “Comparative Study on the Electrochemical Performance of LiFePO4 Cathodes Fabricated by Low Temperature 3D Printing, Direct Ink Writing and Conventional Roller Coating Process
,” Ceram. Int.
, 45
(11
), pp. 14188
–14197
. 30.
Yunker
, P. J.
, Still
, T.
, Lohr
, M. A.
, and Yodh
, A. G.
, 2011
, “Suppression of the Coffee-Ring Effect by Shape-Dependent Capillary Interactions
,” Nature
, 476
(7360
), pp. 308
–311
. 31.
Choi
, S.
, Stassi
, S.
, Pisano
, A. P.
, and Zohdi
, T. I.
, 2010
, “Coffee-Ring Effect-Based Three Dimensional Patterning of Micro/Nanoparticle Assembly With a Single Droplet
,” Langmuir
, 26
(14
), pp. 11690
–11698
. 32.
Sassin
, M. B.
, Garsany
, Y.
, Atkinson
, R. W.
, Hjelm
, R. M. E.
, and Swider-Lyons
, K. E.
, 2019
, “Understanding the Interplay Between Cathode Catalyst Layer Porosity and Thickness on Transport Limitations En Route to High-Performance PEMFCs
,” Int. J. Hydrogen Energy
, 44
(31
), pp. 16944
–16955
. 33.
Owejan
, J. P.
, Owejan
, J. E.
, and Gu
, W.
, 2013
, “Impact of Platinum Loading and Catalyst Layer Structure on PEMFC Performance
,” J. Electrochem. Soc.
, 160
(8
), pp. F824
–F833
. 34.
Bezerra
, C. A. G.
, Deiner
, L. J.
, and Tremiliosi-Filho
, G.
, 2020
, “Inkjet Printed Double-Layered Cathodes for PEM Fuel Cells
,” J. Electrochem. Soc.
, 167
(12
), p. 124503
. Copyright © 2021 by ASME
You do not currently have access to this content.
