Machine and product condition monitoring is important to product quality control, especially for unmanned manufacturing. This paper proposes a technique for the estimation of clearance in mechanical systems under dynamic conditions with specific application to the estimation of backlash in gear systems of servomechanisms. The technique is based on a momentum transfer analysis that shows that the change in the speed (defined as bounce) of the primary gear due to impact with the secondary gear is related to the magnitude of the backlash. An algorithm is presented to estimate the bounce in real-time. The algorithm estimates the bounce by computing the standard bounce which is defined as the standard deviation of the demodulated envelope of the primary gear speed. The standard bounce is shown to be a good measure of the bounce when the system is excited sinusoidally. The algorithm’s accuracy and sensitivity are verified through computer simulation of an open-loop DC servomechanism. An approximately linear relationship between the standard bounce and the backlash magnitude is observed. This holds for backlash values exceeding recommended tolerances by ±100 percent. The algorithm is also shown to be insensitive to changes in the simulation model structure, model parameters as well as system and measurement noise. The estimation technique is accurate, computationally simple, and requires no additional sensors if the servosystem to be monitored already has a conventional tachometer.
Skip Nav Destination
Article navigation
March 1998
Technical Papers
Estimation of Gear Backlash: Theory and Simulation
Jeffrey L. Stein,
Jeffrey L. Stein
Department of Mechanical Engineering and Applied Mechanics, The University of Michigan, Ann Arbor, MI 48109-2125
Search for other works by this author on:
Churn-Hway Wang
Churn-Hway Wang
Ford Motor Company, 21901 Oakwood Blvd, MD 419, Dearborn, MI 48121
Search for other works by this author on:
Jeffrey L. Stein
Department of Mechanical Engineering and Applied Mechanics, The University of Michigan, Ann Arbor, MI 48109-2125
Churn-Hway Wang
Ford Motor Company, 21901 Oakwood Blvd, MD 419, Dearborn, MI 48121
J. Dyn. Sys., Meas., Control. Mar 1998, 120(1): 74-82 (9 pages)
Published Online: March 1, 1998
Article history
Received:
March 13, 1995
Online:
December 3, 2007
Citation
Stein, J. L., and Wang, C. (March 1, 1998). "Estimation of Gear Backlash: Theory and Simulation." ASME. J. Dyn. Sys., Meas., Control. March 1998; 120(1): 74–82. https://doi.org/10.1115/1.2801324
Download citation file:
Get Email Alerts
Offset-Free Koopman Model Predictive Control of Thermal Comfort Regulation for A VRF-DOAS Combined System
J. Dyn. Sys., Meas., Control
Rejection of Sinusoidal Disturbances With Unknown Slowly Time-Varying Frequencies for Linear Time-Varying Systems
J. Dyn. Sys., Meas., Control (July 2024)
Using Control Barrier Functions to Incorporate Observability: Application to Range-Based Target Tracking
J. Dyn. Sys., Meas., Control (July 2024)
Gas Path Fault Diagnosis of Turboshaft Engine Based on Novel Transfer Learning Methods
J. Dyn. Sys., Meas., Control (May 2024)
Related Articles
Wind Turbine Gearbox Fault Detection Using Multiple Sensors With Features Level Data Fusion
J. Eng. Gas Turbines Power (April,2012)
Development and Optimization of Screw Machines With a Simulation Model—Part II: Thermodynamic Performance Simulation and Design Optimization
J. Fluids Eng (September,1997)
Cyber Physical Production Systems for Deep Drawing
J. Manuf. Sci. Eng (October,2023)
Automated Operating Mode Classification for Online Monitoring Systems
J. Vib. Acoust (August,2009)
Related Proceedings Papers
Related Chapters
Expert Systems in Condition Monitoring
Tribology of Mechanical Systems: A Guide to Present and Future Technologies
Introduction
History of Line Pipe Manufacturing in North America
Real-Time Prediction Using Kernel Methods and Data Assimilation
Intelligent Engineering Systems through Artificial Neural Networks