Gas turbine combustion chambers contain numerous small-scale features that help to dampen acoustic waves and alter the acoustic mode shapes. This damping helps to alleviate problems such as thermoacoustic instabilities. During computational fluid dynamics simulations (CFD) of combustion chambers, these small-scale features are often neglected as the corresponding increase in the mesh cell count augments significantly the cost of simulation while the small physical size of these cells can present problems for the stability of the solver. In problems where acoustics are prevalent and critical to the validity of the simulation, the neglected small-scale features and the associated reduction in overall acoustic damping can cause problems with spurious, non-physical noise and prevents accurate simulation of transients and limit cycle oscillations. Low-order dynamical systems (LODS) and artificial neural networks (ANNs) are proposed and tested in their ability to represent a simple two-dimensional acoustically forced simulation of an orifice at multiple frequencies. These models were built using compressible CFD, using OpenFOAM, of an orifice placed between two ducts. The acoustic impedance of the orifice has been computed using the multi-microphone method and compared to a commonly used analytical model. Following this, the flow field downstream of the orifice has been modelled using both a LODS and ANN model. Both methods have shown the ability to closely represent the simulated dynamical flows at much lower computational cost than the original CFD simulation. This work opens the possibility of models that can dynamically predict the flow through, for instance, acoustic liners, dilution ports and fuel injectors in real engines during thermoacoustic instabilities without having to mesh and simulate these small-scale features directly. Such models may also assist in the accurate simulation of flame quenching due to cooling flows or the design of effusion cooled aerodynamic surfaces such as nozzle guide vanes (NGVs) and turbine blades.

This comparative study is concerned with the advances in nozzle guide vane (NGV) design developments and their influence on the film cooling performance by injecting coolant through the purge slot. An experimental study compares the film cooling effectiveness as well as the aerodynamic effects for different purge slot configurations on both a flat and an axisymmetrically contoured endwall of a NGV. While the flat endwall cascade was equipped with four cylindrical vanes, the contoured endwall cascade consisted of four modern NGVs which represent state-of-the-art high-pressure turbine design standards. Geometric variations, e.g. the purge slot width and injection angle, as well as different blowing ratios (BR) at an engine-like density ratio (DR = 1.6) were realized to investigate the real-life effect of thermal expansion, design modifications and the interaction between secondary flow and coolant. The mainstream flow parameters were set to meet real engine conditions with regard to Reynolds and Mach numbers. The Pressure Sensitive Paint (PSP) technique was used to determine the adiabatic film cooling effectiveness. Five-hole probe measurements (DR = 1.0) were performed to measure the flow field with its characteristic vortex structures as well as the loss distribution in the vane wake region. For a more profound insight into the origin and development of the secondary flows, oil dye visualizations were carried out on both endwalls. The measurement results will be discussed based on a side-by-side comparison of the distribution of film cooling effectiveness on the endwall, its area-averaged values as well as the two-dimensional distribution of total pressure losses and the secondary flow field. The results of this study show that the advances in NGV design development have had a significantly positive influence on the distribution of the coolant. This has to be attributed to lesser disturbance of the coolant propagation by secondary flow for the optimized NGV design, since the design features are intended to suppress the formation of secondary flow. In contrast to the results of the cylindrical profile, sufficient cooling can be already provided with a perpendicular injection in the case of the modern NGV. It is therefore advisable to take these effects into account when designing the film cooling system of a modern high-pressure turbine.

Modern gas turbines lean combustors allow to limit NOx pollutant emissions by controlling the flame temperature, while maintaining high turbine inlet temperatures. On the other hand, their adoption presents other challenges, especially concerning the combustor-turbine interaction. Turbine inlet conditions are generally characterized by severe temperature distortions and swirl degree, which, in turn, is responsible for very high turbulence intensities. Several past studies have focused on the description of the effects of these phenomena on the behavior of the high pressure stages of the turbine, both considering them as separated aspects, and, in very recent years, accounting for their combined impact. Nevertheless, very limited experimental results are available when it comes to evaluate the heat transfer coefficient (HTC) on the nozzle guide vane external surface, since relevant temperature distortions present a severe challenge for the commonly adopted measurement techniques. The work presented in this paper was carried out on a non-reactive, annular, three-sector test rig, made by a combustor simulator and a NGV cascade. Making use of three real hardware burners of a Baker Hughes heavy-duty gas turbine, operated in similitude conditions, it can reproduce a representative swirling flow, with temperature distortions at the combustor-turbine interface plane. This test apparatus was exploited to develop an experimental approach to retrieve reliable heat transfer coefficient and adiabatic wall temperature distributions simultaneously, in order to overcome the known limitations imposed by temperature gradients on state-of-the-art methods for HTC calculation from transient tests. A non-cooled mockup of a NGV doublet, manufactured using low thermal diffusivity plastic material, was used for the tests, carried out using IR thermography with a transient approach. In the authors’ knowledge, this presents the first experimental attempt of measuring a nozzle guide vane heat transfer coefficient in the presence of relevant temperature distortions and swirl.

Modern gas turbines present important temperature distortions in the core-engine flowpath, mainly in the form of hot and cold streaks imputed to combustor burners and components cooling systems. As they highly influence turbines performance and lifetime, the precise knowledge of the thermal field evolution through the combustor and the high-pressure turbine is fundamental. The majority of past studies investigated streaks migrations directly examining the thermal field, while a limited amount of experimental work employed approaches based on the detection of tracer gases. The latter approach provides a more detailed evaluation of the evolution and mixing of the different flows. However, the slow time response due to the employment of sampling probes and gas analysers make the investigation of a whole measurement plane extremely time consuming. To tackle this issue, in this study a commercial oxygen sensor element and its excitation/detection unit were integrated into a newly developed probe to carry out local tracer gas concentration measurements exploiting the fluorescence behaviour. The probe was provided with a Kiel-like shield, a pressure port and a thermocouple, in order to correct the readings in case of 3D flows with pressure, temperature and velocity gradients. The paper summarizes the probe development and calibration activities, with the characterization of its accuracy for different flow conditions. Finally, two probe applications are described: firstly the probe was used to detect tracer gas concentrations on a jet flow; afterwards it was traversed on the interface plane between a non-reactive, lean combustor simulator and the NGV cascade. The probe has proven to provide accurate and reliable measurements both from a quantitative and qualitative point of view even in highly 3D flow fields typical of gas turbines conditions.

An increasing number of turboexpanders are equipped with Nozzle Guide Vane (NGV) as the first stator stage. By varying the throat area of the first stator vane the NGV enables an additional control methodology to the line-up power output allowing higher operational flexibility and higher efficiency at partial load and partial speed. The design of this component might become critical for enabling high expander availability considering its exposure to high temperature, thermal loading, and fluid induced vibrations. This is especially true also considering that the vibration frequencies of this sub-assembly are influenced by internal clearances and by the value of the friction coefficient, which leaves a relevant margin of error when using numerical methods (such as FEM) for predicting the actual structural behavior of this component. In this paper, the design of a full-scale test bench for the determination of both friction coefficients and modal behavior of a nozzle guide vane geometry is described. The bench enables us to simulate the pre-load due to aerodynamic forces on the NGV airfoil simulating the actual working conditions of bushes and bearings.

Particles ingested by aero gas turbines are capable of melting in the combustor and depositing on high pressure turbine vane surfaces, where they degrade aerodynamic and thermodynamic performance. The extent of the damage caused is a complex physical process dependent on the thermal and inertial properties of the particles, the operating state of the engine and importantly, engine architecture. The dominant architecture considerations are the position of the burner flames relative to the nozzle guide vane leading edges and the temperature difference across the burner flames. In this work, we investigate the influence of this on particle deposition by approximating the temperature variation of the hot streak as a sinusoidal profile. A parametric analysis is carried out using numerical simulations and an elastic-plastic particle deposition model, to evaluate the effect of mean temperature, temperature difference across the hot streak, and hot streak position on the deposition rate of a generic particle size distribution. Results show that the dominant effect driving particulate deposition is a combination of the gas temperature, hot streak position relative to the vane leading edge and the particulate type. The rate of deposition on a vane for sub-bituminous ash particles may be reduced by up to 56% if the combination of mean temperature, temperature difference across the hot streak, and hot streak position are chosen carefully.

Surface roughness is well known to significantly influence turbine aerodynamics and heat transfer; different studies have been undertaken in the last decades, in order to precisely characterize its effects and pursue a reliable and unified CFD modelling approach. Despite the effort, further research is still required to completely fulfill the goal, due to the complexity of the considered environment, with many other aspects and flow characteristics factoring into the final behavior. In this work an experimental campaign was carried out to evaluate the heat transfer coefficient on a linear nozzle guide vane geometry. The adopted geometry has been developed and tested, at different inlet turbulence intensity, Reynolds and Mach number, at Von Karman Institute. The results achieved on a test article with smooth surface were made available. In the present work the effect of increased turbulence level and surface roughness were taken into account, respectively using passive grids and conditioning the test sample surface finishing. Experiments were conducted using a transient technique by measuring the surface temperature evolution by IR thermography. The collected results integrate the existing database available in the open literature in order to support development and benchmarking of numerical approaches aimed at a reliable characterization of these aspects.

Pressure Gain Combustion (PGC) is considered a possible solution to increase gas turbine cycle efficiency, due to the lower entropy generation in the combustion process. However, the highly unsteady flow produced by PGC makes it more difficult to extract work from its exhaust gas. Any outlet restriction downstream of PGC, such as turbine blades, affects its flow field and may cause additional thermodynamic losses. The unsteadiness in the form of pressure, temperature and velocity vector fluctuations has a negative impact on the operation of conventional turbines. Therefore, evaluating early turbine design parameters for such applications is of great interest. Additionally, experimental measurements and data acquisition present researchers with challenges that have to do mostly with the high temperature exhaust of PGC and the high frequency of its operation. Numerical simulations can provide important insights into PGC exhaust flow and its interaction with turbine blades. In this paper, a Rotating Detonation Combustor (RDC) and a row of nozzle guide vanes have been modeled based on the data from literature and an available experimental setup at TU Berlin. Five guide vane configurations with different geometrical parameters have been modeled. URANS simulations were done for all guide vane arrangements to investigate the effect of solidity and blade type representing different outlet restrictions on the RDC exhaust flow. Total pressure loss and velocity fluctuation were computed upstream and downstream of the vanes. The results analzed the connection between total pressure loss and the vanes solidity and thickness to chord ratio. It is observed that more than 57% of the upstream velocity angle fluctuation amplitude was damped by the vanes. Furthermore, the area reduction was found to be the significant driving factor for damping the velocity angle fluctuations, whether in the form of solidity or thickness on chord ratio increment. A further study of the flow field details revealed that the vane passages act as convergent divergent nozzles in the unsteady flow field and no compression wave exists upstream. This RDC exhaust flow investigation is an important primary step from a turbomachinery standpoint, which provided details of blade behavior in such an unsteady flow field.

Nozzle guide vane platforms often employ complex cooling schemes to mitigate ever-increasing thermal loads on endwall. Understanding the impact of advanced cooling schemes amid the highly complex three-dimensional secondary flow is vital to engine efficiency and durability. This study analyzes and describes the effect of coolant to mainstream blowing ratio, momentum ratio and density ratio for a typical axisymmetric converging nozzle guide vane platform with an upstream doublet staggered, steep-injection, cylindrical hole jet purge cooling scheme. Nominal flow conditions were engine representative and as follows: Ma exit = 0.85, Re exit/Cax = 1.5 × 10 6 and an inlet large-scale freestream turbulence intensity of 16%. Two blowing ratios were investigated, each corresponding to upper and lower engine extrema at M = 3.5 and 2.5, respectively. For each blowing ratio, the coolant to mainstream density ratio was varied between DR = 1.2, representing typical experimental neglect of coolant density, and DR = 1.95, representative of typical engine conditions. An optimal coolant momentum ratio between = 6.3 and 10.2 is identified for in-passage film effectiveness and net heat flux reduction, at which the coolant suppresses and overcomes secondary flows but imparts minimal turbulence and remains attached to endwall. Progression beyond this point leads to cooling effectiveness degradation and increased endwall heat flux. Endwall heat transfer does not scale well with one single parameter; increasing with increasing mass flux for the low density case but decreasing with increasing mass flux of high density coolant. From the results gathered, both coolant to mainstream density ratio and blowing ratio should be considered for accurate testing, analysis and prediction of purge jet cooling scheme performance.

A misalignment between the combustor exit and the nozzle guide vane (NGV) platform commonly exists due to manufacturing tolerances and thermal transience. This study experimentally investigated the effect of the combustor-turbine misalignment on the heat transfer for an axisymmetric converging endwall with a jet purge cooling scheme at transonic conditions. Tests were conducted at engine-representative freestream exit Mach number of 0.85, inlet turbulence intensity of 16%, film cooling blowing ratio of 2.5 (design condition) and 3.5, and density ratio of 1.95. Three different step misalignments, combustor exit 4.9% span higher than turbine inlet (backward-facing), no step (baseline), and combustor exit 4.9% span lower than turbine inlet (forward-facing), were tested to demonstrate the misalignment effect on endwall Nusselt number, adiabatic film cooling effectiveness, and net heat flux reduction. A supportive numerical simulation was conducted to provide insight into the flow field. Experimental and numerical results indicated a blowing ratio of 2.5 amid a backward-facing step leads to more turbulent mixing between the coolant and mainstream due to the horseshoe vortex and step-induced cavity vortex, reducing coolant coverage and adversely affecting coolant performance. For the same blowing ratio, a forward-facing step induced more lift-off and shifted the coverage downstream and toward the pressure side, ultimately slightly enhancing the cooling performance. Nevertheless, the forward-facing step leads to a large cooling effectiveness gradient in the pitch-wise direction. At a blowing ratio of 3.5, the baseline no-step case provided superior coolant performance, however, the effect of the step was much less significant as compared to the lower blowing case. The forward-facing step amid a blowing ratio of 3.5 results in severe jet lift-off, diminishing the returns traditionally associated with increasing coolant mass flow. Based on this study, a backward-facing step should be avoided to prevent endwall burnout in the nozzle guide. Additionally, a forward-facing step should be avoided, especially amid high blowing ratios.

This paper presents WMLES simulations of a chute type turbine rim seal. Configurations with an axisymmetric annulus flow and with nozzle guide vanes fitted (but without rotor blades) are considered. The passive scalar concentration solution and WMLES are validated against available data in the literature for uniform convection and a rotor-stator cavity flow. The WMLES approach is shown to be effective, giving significant improvements over an eddy viscosity turbulence model, in prediction of rim seal effectiveness compared to research rig measurements. WMLES requires considerably less computational time than wall-resolved LES, and has the potential for extension to engine conditions. All WMLES solutions show rotating inertial waves in the chute seal. Good agreement between WMLES and measurements for sealing effectiveness in the configuration without vanes is found. For cases with vanes fitted the WMLES simulation shows less ingestion than the measurements, and possible reasons are discussed.

Flow over gas turbine endwalls is complex and highly three-dimensional. As boundaries for modern engine designs are pushed, this already-complex flow is affected by aggressive application of film cooling flows that actively interact. This two-part study describes, experimentally, the aero-thermal interaction of cooling flows near the endwall of a first stage nozzle guide vane passage. The approach flow conditions represent flow exiting a low-NOx combustor. The test section includes geometric and cooling details of a combustor-turbine interface in addition to endwall film cooling flows injected upstream of the passage. The first part of this study describes in detail, the passage aerodynamics as affected by injection of cooling flows. It reveals a system of secondary flows, including the newly-discovered Impingement Vortex , which redefines our understanding of the aerodynamics of flow in a modern, film-cooled, first-stage vane row. The second part investigates, through thermal measurements, the distribution, mixing and disruption of cooling flows over the endwall. Measurements are made with and without active endwall film cooling. Descriptions are made through adiabatic surface effectiveness measurements and correlations with in-passage velocity (presented in part one) and thermal fields. Results show that the newly-discovered impingement vortex has a positive effect on coolant distribution through passage vortex suppression and by carrying the coolant to hard-to-cool regions in the passage, including the pressure surface near the endwall.

Modern gas turbines are subjected to very high thermal loading. This leads to a need for aggressive cooling to protect components from damage. Endwalls are particularly challenging to cool due to a complex system of secondary flows near them that wash and disrupt the protective coolant films. This highly three-dimensional flow not only affects but is also affected by the momentum of film cooling flows, whether injected just upstream of the passage to intentionally cool the endwall, or as combustor cooling flows injected further upstream in the engine. This complex interaction between the different cooling flows and passage aerodynamics has been recently studied in a first stage nozzle guide vane. The present paper presents a detailed study on the sensitivity of aero-thermal interactions to endwall film cooling MFR (cooling mass flow to mainstream flow ratio). The test section represents a first stage nozzle guide vane with a contoured endwall and endwall film cooling injected just upstream of it. The test section also includes an engine-representative combustor-turbine interface geometry with combustor cooling flows injected at a constant rate. The approach flow conditions represent flow exiting a low-NOx combustor. Adiabatic surface thermal measurements and in-passage velocity and thermal field measurements are presented and discussed. The results show the dynamics of passage vortex suppression and the increase of impingement vortex strength as MFR changes. The effects of these changes of secondary flows on coolant distribution are presented.

Under the effect of inlet distortion profiles (including hot-streaks, total pressure profiles, and swirling flow angle patterns), the film cooling performance on the leading edge (LE) region of GE-E 3 nozzle guide vanes (NGVs) has been numerically investigated in this paper. Firstly, the complicated inlet distortion profiles of a low NO x combustor chamber has been decoupled to single factors to explore the individual and the coupling effects on the film cooling performance of the NGV LE region (Case 1 to Case 4). Then the original and three modified film-hole configurations are compared and discussed under the quasi-real environment (Case 5 to Case 8). The results indicate that total pressure profile tends to draw more coolant toward the midspan and the residual swirl promotes turnover of the cooling film to the other side of NGVs near the enwalls of LE region. Under the combined effects of different distortion profiles, the cooling film is redistributed on the LE region with some area near the stagnation lines with poor coverage. The upwash or downwash of boundary layer fluid caused by the complicated vortex in passages draws the cooling film on NGV surfaces. And this effect will be strengthened or weakened by the injection angles of holes. Finally, the filmhole configuration in Case 8 with counter-inclined film-hole rows arranged along the stagnation lines shows the best film cooling performance, which has positive effects on the decrease of high temperature region induced by hot streak (HS), and results in more uniform temperature distribution.

The first stage turbine of a modern gas turbine is subjected to high thermal loads which lead to a need for aggressive cooling schemes to protect its components from melting. Endwalls are particularly challenging to cool due to the complex system of secondary flows near them that wash the protective film coolants into the mainstream. This paper shows that without including combustor cooling, the complex secondary flow physics are not representative of modern engines. Aggressive injection of all cooling flows upstream of the passage is expected to interact and change passage aerodynamics and, subsequently, mixing and transport of coolants. This study describes, experimentally, the aero-thermal interaction of cooling flows near the endwall of a first stage nozzle guide vane passage. The test section involves an engine-representative combustor-turbine interface geometry, combustor coolant flow and endwall film cooling flow injected upstream of a linear cascade. The approach flow conditions represent flow exiting a cooled, low-NOx combustor. This first part of this two-part study aims to understand the complex aerodynamics near the endwall through detailed measurements of passage three-dimensional velocity fields with and without endwall film cooling. The aerodynamic measurements reveal a dominant vortex in the passage, named here as the Impingement Vortex, that opposes the passage vortex formed at the airfoil leading edge plane. This Impingement Vortex completely changes our description of flow over a modern film cooled endwall.

This paper presents the Large Eddy Simulation (LES) of a Low-Pressure Turbine (LPT) Nozzle Guide Vane (NGV) for different Reynolds (Re) and Mach number (Ma). The analysis is based on a slice of the blade that may be representative of midspan flow where secondary flows, hub and shroud contributions are lower. In LPT, the variation of the Re during the mission of the gas turbine is a well-known effect since its value can vary of a factor four between take-off and cruise. This can induce performance variations due to various phenomena with among them suction side boundary layer separation on the aft portion of the blade due to an adverse pressure gradient and laminar boundary layer that can be maintained due to the relatively low Re in LPT. Similarly, the Ma in the LPT may vary depending on the thrust required from the gas turbine at the considered mission phase. The current paper investigates through numerical simulation the flow representative of a medium-sized LPT with three different Reynolds number Re = 175’000 (cruise), 280’000 (mid-level altitude) and 500’000 (take-off) keeping the same characteristic Mach number Ma = 0.2 and three different Mach number Ma = 0.2, 0.5 and 0.8 keeping the same Reynolds number Re = 280’000. The study focuses on different flow characteristics: pressure distribution around the blade, near-wall flow behavior and wake analysis. This includes the related generation of losses and the effect of Re and Ma on these different phenomena. A special emphasis is given to the generation of loss based on an entropy approach and the redistribution of mean kinetic energy towards turbulent kinetic energy. The results show that the increase of the Re has a destabilizing effect on potential separation while the increase of the Ma has a stabilizing effect. The peak in the TKE downstream of the blade is also moved upstream closer to the trailing edge when the Ma is increased.

Particle ingestion is a major concern for the operation of gas turbines. In the case of an aircraft, particle dispersed in the air ingested by the engine can threaten flight safety. Swallowed particles can erode or stick to aerodynamic surfaces. Both the occurrences translate in a reduction of performance due to variation in shape and in roughness of the aerodynamic surfaces. This work is devoted to the analysis of fouling, i.e. the deposition of particles over time. By observing that the deposition pattern is strongly influenced by the flow field in the nearby of the walls, the central idea of this work is to employ Active Flow Control (AFC) to mitigate fouling when emergency conditions are met by the aircraft. The proposed system will inject air bled from compressor discharge in front of the critical locations where fouling is supposed to occur. The present work aspires to lay the foundations for the development of such an AFC device, by focusing on the modified aerodynamics consequent to the introduction of the transverse jet. The potential of this device is evaluated quantitatively using CFD simulations. An energy-based sticking model, coupled with a mesh-morphing solver, is used to track the airfoil deposition thickness evolution in time. The work is two-fold: first, the dynamics of the interaction between flow structures and particle transport is addressed. Second, the attention is posed on correlating fouling pattern variation to the modified aerodynamics of the vane consequent to the introduction of the device. Three design concepts are investigated on the 3D test case geometry of an HPT NGV cascade. The counter-rotating vortex pair (CVP) is detected as the main responsible for jet-particle interaction. Finally, the jet impact on aerodynamic performance is also assessed.

This study includes the design, validation, and fabrication via Direct Metal Laser Sintering (DMLS) of a gas turbine nozzle guide vanes (NGV) that incorporates three innovative cooling schemes specifically enabled by additive manufacturing. The novel NGV design is the culmination of an extensive research and development effort over a period of four years that included low and high speed cascade testing coupled with unsteady CFD for numerous candidate innovative cooling architectures. The final vane design (SJ-vane) consists of sweeping jet (SJ) film cooling holes on the suction surface, sweeping jet impingement holes at the leading edge and double-wall partial length triangular pin-fin with impinging jet at the trailing edge. For comparison purposes, a second DMLS enabled vane (777-vane) was designed and fabricated with prototypical cooling circuits to serve as a baseline. This vane consists of a shaped film cooling holes on the suction surface, circular impingement holes at the leading edge and full length cylindrical pin-fins at the trailing edge. Experiments with the two DMLS enabled vanes were performed at the Ohio State University Turbine Reacting Flow Rig (TuRFR) at engine relevant temperature (1375K) and Mach number conditions. Infrared (IR) thermography was utilized to measure the wall temperature of the pressure and suction surface at several coolant mass flow rates to estimate the overall cooling effectiveness (ϕ). Results showed improved cooling performance for the advanced cooling schemes (sweeping jet film cooling, impingement cooling and triangular pin-fin cooling) compared to the baseline cooling schemes.

In this work, the effects of Turbine Center Frame (TCF) wakes on the aeromechanical behavior of the downstream Low Pressure Turbine (LPT) blades are numerically investigated and compared with experimental data. A small industrial gas turbine has been selected as a test case, composed of a TCF followed by the two low pressure stages and a Turbine Rear Frame (TRF) before the exhaust plenum. Full annulus unsteady computations of the whole low-pressure module have been performed. Two operating conditions, full (100%) and partial (50%) load, have been investigated with the aim of highlighting the impact of TCF wakes convection and diffusion through the downstream rows. Attention was paid to the harmonic content of rotors’ blades. From an aerodynamic point of view, the results show a slower decay of the wakes through the downstream rows in off-design conditions as compared to the design point. The wakes generated by the struts at partial load persist throughout the domain outlet, while they are chopped and circumferentially transported by the rotors motion. This is due to the strong incidence variation at which the TCF works, which induces the growth of wide regions of separated flow on the rear part of the struts. Nevertheless, the analysis of the rotors’ frequency spectrum reveals that moving from design to off-design conditions, the effect of the TCF does not change significantly, thanks to the filtering action of the first LPT stage movable Nozzle Guide Vane (NGV). From unsteady calculations the harmonic contribution of all turbine components has been extracted, highlighting the effect of statoric parts on the last LPT blade. Anyhow the TCF harmonic content remains the most relevant from an aeromechanic point of view as per experimental evidence, and it is considered for a Forced Response Analysis (FRA) on the last LPT blade itself. Finally, aerodynamic and aeromechanic predictions have been compared with the experimental data to validate the numerical approach. In the last part of this paper some general design solutions, that can help mitigation of the TCF wakes impact, are discussed.

Nozzle guide vanes (NGVs) and rotor blades deteriorate due to erosion, and this may affect the aerodynamic characteristics of gas turbines. According to previous studies, the erosion of first-stage NGVs significantly affected the blade loading of the first-stage rotor. An increase in the tip gap also may significantly affect the gas turbine performance. In the present study, numerical investigations have been carried out using a real eroded nozzle and blade geometries for two purposes. One purpose was to clarify the influences underlying the deterioration of the nozzle and the rotor blade, such as the effects on the erosion of NGVs in the first stage and the effects of the tip gap on the gas turbine performance. The other was to develop a method to estimate the total gas turbine performance using a CFD simulation and a heat balance analysis. The results show that the erosion of NGV leads to an increased flow rate and affects the operating condition of the gas turbine cycle. This, in turn, can decrease the total thermal efficiency. The experimental results suggest that an increase in the tip gap width decreases rotor output almost linearly, and the numerical results showed the same tendency. The influence of the tip gap in the real gas turbine condition was also examined, revealing that an increase in the tip gap leads to an increase in the pressure loss in the nozzle downstream as well as around the rotor blade itself. Consequently, the total power output and the isentropic efficiency of the turbine decreased.